Werbung
Verfügbare Sprachen
Verfügbare Sprachen
34 | English
Table saw
Rated power input
Rated voltage
Frequency
No-load speed
Starting current limitation
Weight according to EPTA-Procedure 01:2014
Protection class
Dimensions (including detachable parts of the tool)
Width x depth x height
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Min. tooth thickness/offset
Hole diameter
Maximum workpiece dimensions: (see "Maximum workpiece dimensions", page 38)
Noise information
Noise emission values determined according to
EN 62841-3-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 94 dB(A); sound power level
103 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Table saw with fitted saw blade (24) and riving knife (4)
– Angle guide (2)
1 609 92A 5UC | (18.09.2020)
GTS 635-216
W
1600
V
220 − 240
Hz
50/60
-1
min
5500
kg
22
/ II
mm
658 x 332 x 553
mm
216
mm
1.5 − 2.1
mm
2.3
mm
30
– Parallel guide (5)
– Additional parallel guide (41)
– "Additional parallel guide" fastening set (42) (2 fastening
screws, 2 washers, 2 wing nuts)
– Protective cover (3)
– Hex key (10)
– Ring spanner (9) with slotted screwdriver tip
– Push stick (12)
– Table insert (23)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
– Turn the locking screws (32) as far as possible in the "Un-
lock" direction using the tip of the ring spanner (9) and
open the base grid (31) (see figure a).
Remove the packing material under the motor block.
The following tool elements are attached directly to the tool
housing: Push stick (12), ring spanner (9), hex key (10),
parallel guide (5), angle guide (2), extraction adapter (29),
additional parallel guide (41) with fastening set (42), pro-
tective cover (3).
GTS 635-216
1600
220 − 240
50/60
5500
●
●
22
/ II
658 x 332 x 553
216
1.5 − 2.1
2.3
25.4
Bosch Power Tools
Werbung
