Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Scale for spacing between saw blade and parallel
guide
(2)
Angle guide
(3)
Protective cover
(4)
Riving knife
(5)
Parallel guide
(6)
Saw table expansion
(7)
Angle guide storage compartment
(8)
Assembly holes
(9)
Ring spanner (24 mm; 23 mm)
(10)
Hex key (5 mm)
(11)
Bracket for storing the protective cover
(12)
Push stick
(13)
Clamping handle for saw table expansion
(14)
Hand wheel
(15)
Crank for raising and lowering the saw blade
(16)
Safety flap for the on/off switch
(17)
Stop for 45° bevel angle
(18)
Locking lever for setting the bevel angle
(19)
Scale for bevel angles
(20)
Stop for 0° bevel angle
(21)
Saw table
(22)
Adjusting screw for adjusting the clamping force of
the parallel guide
(23)
Table insert
(24)
Saw blade
(25)
Guide groove for parallel guide
(26)
Cable holder
(27)
Carrying handle
(28)
Guide groove for angle guide
(29)
Dust extraction adapter
V guide groove on the saw table for the parallel
(30)
guide
(31)
Base plate
(32)
Locking screw for base grid
(33)
Clamping lever/clamp markings
(34)
Clamping lever for riving knife
Technical data
Table saw
Article number
Bosch Power Tools
(35)
Positioning pins for riving knife
(36)
Table insert locking screw
(37)
Clamping lever for protective cover
(38)
Guide pin for protective cover
(39)
Clamping handle for parallel guide
(40)
V guide for parallel guide
(41)
Additional parallel guide
(42)
"Additional parallel guide" fastening set
(43)
Guide rail for angle guide
(44)
Lower saw blade cover
(45)
Tab for lower saw blade cover
(46)
Gripping hole for lifting the table insert
(47)
Clamping nut
(48)
Spindle locking lever
(49)
Clamping flange
(50)
Mounting flange
(51)
Tool spindle
(52)
Angle indicator (vertical)
(53)
Locking knob for all mitre angles
(54)
Angle indicator on the angle guide
(55)
Magnifying glass
(56)
Saw table spacing indicator
(57)
On button
(58)
Viewing window
(59)
Cross-head screw for setting the 0° stop
(60)
Screw for bevel angle indicator
(61)
Cross-head screw for setting the 45° stop
(62)
Hex socket screws (5 mm) on the front for adjust-
ing the parallelism of the saw blade
(63)
Hex socket screws (5 mm) on the rear for adjust-
ing the parallelism of the saw blade
(64)
Screw for saw table spacing indicator
(65)
Hex socket screws (5 mm) for adjusting the paral-
lelism of the parallel guide
(66)
Screw for parallel guide spacing indicator
(67)
Adjusting screws for table insert
Push stick storage compartment
(68)
(69)
Hex key storage compartment
(70)
Ring spanner storage compartment
GTS 635-216
3 601 M42 001
3 601 M42 031
3 601 M42 071
3 601 M42 041
English | 33
GTS 635-216
3 601 M42 0B1
1 609 92A 5UC | (18.09.2020)
Werbung
