Herunterladen Inhalt Inhalt Diese Seite drucken

Preset Memory; Operating Component Stored In The Preset Memory - Denon AVR-550SD, SYS-550SD Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 47

Preset memory

DENON and other makes of components can be operated by setting the preset memory.
This remote control unit can be used to operate components of other manufacturers without using the learning
function by registering the manufacturer of the component as shown on the List of Preset Codes (pages
311~313).
Operation is not possible for some models.
1
Set mode switch 1 to "AUDIO" or "VIDEO".
Set the AUDIO side for the CD, Tape deck or
CDR/MD position, to the VIDEO side for the
DVD/VDP, DBS/CABLE, VCR or TV position.
2
Set mode switch 2 to the component to be
registered.
3
Press the ON/SOURCE button and the OFF
button at the same time.
• Indicator flash.
4
Referring to the included List of Preset Codes, use the number buttons to input the
1
2
3
preset code (a 3-digit number) for the manufacturer of the component whose
4
5
6
signals you want to store in the memory.
7
8
9
0
5
To store the codes of another component in the memory, repeat steps 1 to 4.
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental
operation, cover the remote control unit's transmitting window while setting the preset memory.
• Depending on the model and year of manufacture, this function cannot be used for some models, even if
they are of makes listed on the included list of preset codes.
• Some manufacturers use more than one type of remote control code. Refer to the included list of preset
codes to change the number and check.
• The preset memory can be set for one component only among the following: CDR/MD, DVD/VDP
and DBS/CABLE.
The preset codes are as follows upon shipment from the factory and after resetting:
TV, VCR......................................................................HITACHI
CD, TAPE ...................................................................DENON
CDR/MD ....................................................................DENON (CDR)
DVD/VDP ...................................................................DENON (DVD)
DBS/CABLE ...............................................................ABC (CABLE)

Operating component stored in the preset memory

1
3
2
4
1
2
3
1. Digital video disc player (DVD) system buttons
POWER : Power on/standby
(ON/SOURCE)
6
8
0~9, +10 : 10 key
DISC SKIP : Disc skip
DISPLAY : Switch display
MENU
RETURN : Return
SETUP
D, H, F, G : Cursor up, down, left
ENTER : Enter setting
NOTE:
• Some manufacturers use different names for
Set mode switch 1 to "AUDIO" or "VIDEO".
Set the AUDIO side for the CD, tape deck or
CDR/MD position, to the VIDEO side for the
DVD/VDP, DBS/CABLE, VCR or TV position.
Set mode switch 2 to the component you want
to operate.
Operate the component.
• For details, refer to the component's operating instructions.
Some models cannot be operated with this remote control unit.
OFF
: DENON DVD Power
off
,
: Manual search
7
(forward and reverse)
2
: Stop
: Play
1
,
: Auto search
9
(to beginning of track)
3
: Pause
+
(for DVD changer only)
: Menu
: Setup
and right
the DVD remote control buttons, so also refer to
the instructions on remote control for that
component.
ENGLISH
3
3
1
2
3
2. Video disc player (VDP) system buttons
POWER : Power on/standby
(ON/SOURCE)
,
: Manual search
6
7
(forward and reverse)
: Stop
2
1
: Play
8
,
9
: Auto search (cue)
: Pause
3
0~9, +10 : 10 key
17

Werbung

Inhaltsverzeichnis

Fehlerbehebung

loading

Inhaltsverzeichnis