Makita UR013G Betriebsanleitung Seite 23

2-tooth/3-tooth/4-tooth blades, nylon
cutting head, and plastic blade
T h e s e c u t t i n g t o o l s a r e u s e f u l f o r c u t t i n g g r a s s a n d
w e e d s . S w i n g t h e t o o l e v e n l y i n a h a l f - c i r c l e f r o m
t o l e f t . R e p e a t r i g h t - t o - l e f t s t r o k e w h i l e a d v a n c i n g
f o r w a r d .
Fig.36
W hen using a nylon cutting head (bump & feed
type)
T h e n y l o n c u t t i n g h e a d i s a d u a l s t r i n g t r i m m e r h e a d
p r o v i d e d w i t h a b u m p & f e e d m e c h a n i s m .
T o f e e d o u t t h e n y l o n c o r d , t a p t h e c u t t i n g h e a d a g a i n s t
t h e g r o u n d w h i l e r o t a t i n g .
Fig.37: 1. Most effective cutting area
NOTICE:
The bump feed w ill not operate prop-
erly if the nylon cutting head is not rotating.
NOTE: I f t h e n y l o n c o r d d o e s n o t f e e d o u t w h i l e
t a p p i n g t h e h e a d , r e w i n d / r e p l a c e t h e n y l o n c o r d
b y f o l l o w i n g t h e p r o c e d u r e s i n t h e s e c t i o n f o r t h e
m a i n t e n a n c e .
Chisel blade
CAUTION:
Never cut trees larger than 70 mm
diameter.
T h e c h i s e l b l a d e i s u s e f u l f o r c u t t i n g s h r u b s a n d t r e e s .
T o a v o i d k i c k b a c k , a l w a y s a p p l y t h e s e g m e n t o f t h e
c h i s e l b l a d e b e t w e e n 8 a n d 11 o ' c l o c k t o a t r e e .
Fig.38: 1. 8 t o 11 o ' c l o c k s e g m e n t o f t h e b l a d e
F o r e a s e o f c u t t i n g a t r e e , s u p p o r t t h e p r o t e c t o r a g a i n s t
t h e t r e e s t e m a s i l l u s t r a t e d .
Fig.39
Shredder blade
CAUTION:
Never raise the tool head higher
than your w aist height.
CAUTION:
Never perform up-and-do w n
stroke w ith the cutting tool other than the shred-
der blade.
S h r e d d e r b l a d e i s u s e f u l f o r c u t t i n g o p e n a d e n s e b u s h
a n d s h r e d d i n g g r a s s . S w i n g t h e t o o l h e a d u p a n d d o w n ,
o r l e f t a n d r i g h t o n t o t h e b u s h .
Fig.40
Fig.41
MAINTENANCE
WARNING:
r i g h t
switched off and battery cartridge is removed
before attempting to perform inspection or main-
tenance on the tool. Failure to switch off and remove
t h e b a t t e r y c a r t r i d g e m a y r e s u l t i n s e r i o u s p e r s o n a l
injury from accidental start-up.
NOTICE:
alcohol or the like. Discoloration, deformation or
cracks may result.
T o m a i n t a i n p r o d u c t S A F E T Y a n d R E L IA B I L I T Y ,
repairs, any other maintenance or adjustment should
b e p e r f o r m e d b y M a k i t a A u t h o r i z e d o r F a c t o r y S e r v i c e
C e n t e r s , a l w a y s u s i n g M a k i t a r e p l a c e m e n t p a r t s .
Cleaning the tool
Clean the tool by wiping off dust, dirt, or cut off grass
w i t h a d r y c l o t h o r o n e d i p p e d i n s o a p y w a t e r a n d w r u n g
o u t . T o a v o i d o v e r h e a t i n g o f t h e t o o l , b e s u r e t o r e m o v e
the cut off grass or debris adhered to the vent of the
t o o l .
Replacing the nylon cord
WARNING:
diameter specified in this instruction manual.
Never use heavier line, metal w ire, rope or the
like. F a i l u r e t o d o s o m a y c a u s e d a m a g e t o t h e t o o l
and result in serious personal injury.
WARNING:
head from the tool w hen replacing the nylon cord.
WARNING:
nylon cutting head is secured to the housing
properly as described in this instruction manual.
F a i l u r e t o p r o p e r l y s e c u r e t h e c o v e r m a y c a u s e t h e
nylon cutting head to fly apart resulting in serious
personal injury.
R e p l a c e t h e n y l o n c o r d i f i t i s n o t f e d a n y m o r e . T h e
m e t h o d o f r e p l a c i n g t h e n y l o n c o r d v a r i e s d e p e n d i n g o n
t h e t y p e o f t h e n y l o n c u t t i n g h e a d .
B& F Z 5L
Fig.42
Replacing the plastic blade
R e p l a c e t h e p l a s t i c b l a d e i f i t i s w o r n o u t o r b r o k e n .
Fig.43
W h e n i n s t a l l i n g t h e p l a s t i c b l a d e , a l i g n t h e d i r e c t i o n o f
t h e a r r o w o n t h e b l a d e w i t h t h a t o f t h e p r o t e c t o r .
Fig.44: 1. A r r o w o n t h e p r o t e c t o r 2. A r r o w o n t h e
b l a d e
23 ENGLISH
Al w ays be sure that the tool is
Never use gasoline, ben z ine, thinner,
Use only the nylon cord w ith
Al w ays remove the nylon cutting
Make sure that the cover of the