Not Covered; Technical Information - Barbecook STELLA 3201 Benutzerhandbuch

replacement of defective parts.

12.2. Not covered

The following damage and defects are not covered by the
warranty:
• Normal wear and tear (rust, deformation, discoloration, etc.)
of parts that are directly exposed to re or intense heat.
These parts will need to be replaced from time to time.
• Visual irregularities that are inherent to the manufacturing
process (blemishes, minimal deviations and color deviations
in the enamel). These irregularities are not regarded as
manufacturing defects.
• All damage caused by inadequate maintenance, improper
storage, incorrect assembly, or modi cations made to the
pre-assembled parts.
• All damage caused by the misuse of the appliance (not
using it according to the instructions in our guide, using it
for commercial purposes, etc.).
14. RECTIFYING PROBLEMS
Problem
Insufficient heat
Too hot and/or flare-ups
Heat not evenly distributed
over grill surface
Yellow flames
Incomplete flame
Problem
Flashbacks (flames outside
of venturi tubes/at control
knobs)
Flames higher than edge of
bowl
Pressure regulator buzzing
Burner whistles when set to
LOW
Igniting burner fails (both with
igniter and match)
Igniting burners fails with
igniter
Potential causes
• Gas supply not open
• Venturi tubes not situated above the
openings of the gas valves
• Burner openings blocked
• Gas bottle (almost) empty
• Pressure regulator not correctly connected
to bottle and/or hose
• Food too fatty
• Fat drain openings blocked, fat in bowl, and/
or on burners
• Temperature too high
• Some difference in heat is normal, see
"1.7 Using the heat ef ciently" and "10.6
Using the heat zones". Potential causes of
considerable differences in heat:
• Appliance not pre-heated
• Burners or venturi tubes blocked
• Salt on burners
• Appliance connected to butane
• Burner blocked, pierced, or corroded
Potential causes
• Burners or venturi tubes blocked
• Wind
• Gas bottle (almost) empty
• Fat in bowl and/or on burners
• Warm weather
• New (full) gas bottle
• Gas injector, venturi tube, and/or burner
soiled
• Burner or venturi tube blocked
• No gas supply
• No battery inserted or battery inserted
incorrectly
• Middle burner not ignited rst
• Igniter wiring not correctly connected
• Electrode damaged
• Incorrect grounding
• Defective igniter
www.barbecook.com
• All consequential damage caused by careless or non-
compliant use of the appliance.
• Rust or discoloration as a result of external factors, use of
aggressive cleaning agents, exposure to chlorine etc. This
damage is not regarded as a manufacturing defect.

13. TECHNICAL INFORMATION

13.1. Type label
The type label bears all technical information for the appliance.
You will find this number:
• In the second part of this guide.
• On the inside of the gas barbecue.
13.2. Diameters of the injectors
• Main burner: 0.991 mm
• Side burner: 0.88 mm
Solutions
• Open gas supply
• Place venturi tubes above the openings of
the gas valves
• Clean burner openings or replace burners
• Replace gas bottle
• Reconnect pressure regulator to bottle and/
or hose
• Cut off excess fat or select a lower heat for
the burners
• Clean fat drain opening, bowl, and burners
• Select a lower heat for the burners and/or
grill food indirectly
• Pre-heat appliance
• Clean burners and venturi tubes
• Clean burners
• Connect appliance to propane and use a
suitable pressure regulator
• Clean or replace burner
Solutions
• Close the gas supply and set the burners to
OFF.
• Allow the appliance to cool.
• Clean burners and venturi tubes.
• Turn rear of appliance to wind
• Replace gas bottle
• Clean bowl and burners
• No hazard or fault; stops automatically after
a short period of time.
• Clean gas injector, venturi tube, and burner
• Clean burner and venturi tube
• Open gas supply and press safety button
on pressure regulator (not present on all
regulators)
• Re-insert/insert battery with correct polarity
• Ignite middle burner rst
• Check all igniter connections and re-connect
• Replace electrode
• Check electrodes, burners, and igniter and
re-assemble
• Replace igniter
33