Useful Tips And Tricks - Barbecook STELLA 3201 Benutzerhandbuch

consult "14. Rectifying problems" in order to identify the
cause of the problem.
8. If one burner has been ignited, you can ignite the other
burners by setting the relevant control knobs to HIGH.
9.3. Igniting the side burner
The side burner can only hold pans with a maximum
weight of 9 kg and a maximum diameter of 220 mm.
The lid on the side burner must remain open when the side
burner is in use.
9.3.1 Using the igniter
1. Open the lid and set the control knob for the side burner to
OFF.
2. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
3. Press the control knob for the side burner, set it to HIGH,
and leave it in place. The in-built igniter will create sparks,
which will ignite the side burner.
4. If the burner does not ignite after three attempts, set the
control knob for the burner to OFF, close the gas supply, and
wait for 5 minutes to allow the accumulated gas to escape.
5. Attempt to ignite the side burner again. If it still does not
ignite, attempt to ignite the burner with a match or consult
"14. Rectifying problems" in order to identify the cause of the
problem.
9.3.2 Using a match
1. Place a match in the match holder.
2. Open the lid and set the control knob for the side burner to
OFF.
3. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
4. Strike the match and hold it around 13 mm away from the
side burner.
5. Set the control knob for the side burner to HIGH.
6. If the side burner does not ignite within 5 seconds, set the
control knob for the burner to OFF, close the gas supply, and
wait for 5 minutes to allow the accumulated gas to escape.
7. Attempt to ignite the side burner again. If this does not work,
consult "14. Rectifying problems" in order to identify the
cause of the problem.
9.4. Switching the burners off
If the burners will not be used for some time, they must be
switched off. Proceed as follows:
1. Close the gas supply.
2. Set the control knobs for the burners to OFF.
By closing the gas supply first, you ensure there is no
longer any gas present in the appliance.
9.5. Re-igniting the burners
If a burner goes out in use, proceed as follows:
30
1. Open the lid and close the gas supply.
2. Set all control knobs to OFF and wait for 5 minutes for the
accumulated gas to escape.
3. Re-ignite the burner(s).
9.6. Checking the flames
Whenever you ignite a burner, you must check its flames. A
perfect flame will be almost blue, with a small amount of yellow
at the top. Sporadic yellow flames are normal and safe.
If there is a problem with the flames, take one of the following
measures to rectify it:
The flames are...
Low and entirely yellow 1. Close the gas supply
Higher than the bowl

10. USEFUL TIPS AND TRICKS

10.1. Pre-heating the appliance
Pre-heating the appliance ensures that the grill is hot enough
when you come to place food on it. Proceed as follows:
1. Ignite the burner(s) and set the control knob(s) to HIGH.
2. Close the lid and allow the appliance to burn for ten minutes.
3. After ten minutes, open the lid and place the food on the grill.
4. If you want less heat, set the control knob(s) to a lower heat.
10.2. Preventing food from sticking
To prevent your food from sticking to the grill:
• Oil the food lightly with a brush before placing it on the grill.
You can also oil the grill itself.
• Pre-heat the appliance. The hotter the grill when you place
the food on it, the less the chance of the food sticking.
• Do not turn the food too quickly. First allow it to heat up
thoroughly.
10.3. Grilling directly and indirectly
You can grill directly or indirectly depending on the type of food
that you want to cook and the way in which you want to do it:
www.barbecook.com
Proceed as follows...
immediately and set all control
knobs to OFF.
2. Consult "14. Rectifying
problems" in order to identify
the cause of the problem. The
venturi tubes are most likely
blocked.
1. Close the gas supply
immediately and set all control
knobs to OFF.
2. Wait for 5 minutes to allow the
accumulated gas to escape.
3. Re-ignite the burner(s).
4. If this does not rectify the
problem, consult "14. Rectifying
problems" in order to identify the
cause.