Assembling The Appliance; Safety Instructions; To Assemble The Appliance - Barbecook STELLA 3201 Benutzerhandbuch

4.3. Enamel
Some parts of the appliance are covered in a layer of melted
glass, also known as enamel. This enamel protects the
underlying metal from corrosion. Enamel is a high-quality
material: it is corrosion-resistant, it does not degrade under the
influence of high temperatures, and it is very easy to maintain.
Since the enamel is less flexible than the metal to which
it is applied, pieces of enamel may break off when the
appliance is used incorrectly. To avoid this problem, you
must be careful when assembling enameled parts and
you must always maintain the enamel according to the
instructions in this guide.
4.4. Flare-ups
Flare-ups are sudden flames that spark from the bowl
when you are grilling. They are usually caused by dripping
fat or marinade.
5.

ASSEMBLING THE APPLIANCE

5.1. Safety instructions

• Do not make modi cations to the appliance when
assembling. Parts pre- tted and/or sealed by the
manufacturer must not be modi ed as doing so presents a
hazard.
• Always follow the assembly instructions carefully.
• The user is responsible for the correct assembly of the
appliance. Damage caused by incorrect assembly is not
covered by the warranty.

5.2. To assemble the appliance

You require a Phillips screwdriver, a flat-head screwdriver, and
an AA battery (for the electrical igniter). The appliance is not
26
supplied with batteries.
1. Place the appliance on a flat and stable surface.
2. Assemble the appliance as shown in the assembly drawings.
You can find the assembly drawings in the second part of
this guide, after the exploded drawing of your appliance
(see page 90).
Take care when assembling enameled parts. The tool
and the screws may damage the enamel. Use the fiber
washers supplied to protect the enamel around the screws.
The blister packaging may contain more screws than
needed, in which case there will be some screws left over
after assembly.
6. FITTING THE APPLIANCE WITH GAS
6.1. Which gas bottle, hose, and regulator?
To fit the appliance with gas, you will firstly need to purchase a
gas bottle, a hose, and a pressure regulator. The table below
indicates which gas bottle, hose, and regulator you should use.
In Belgium (BE), for example, you must use a propane bottle
with a hose and regulator for 37 mbar, or a butane bottle with
hose and regulator for 28-30 mbar.
Country
LU - NL - DK - FI
- SE - CY - CZ -
EE - LT - MT - SK
- SI - BG -IS - NO
TR - HR - RO - IT
- HU - LV
BE - FR - IT - LU -
IE - GR - PT - ES
- CY - CZ - LT -
SK - CH - SI - LV
The appliance has been designed to be used with butane
or propane bottles of 4.5 to 15 kg and equipped with
an appropriate reducer valve. We recommend using
propane with the appliance. Propane delivers high-quality
combustion and is less sensitive to frost. The height of the
gas bottle must not exceed 70 cm, irrespective of the width
or diameter D or the bottle.
Always purchase your pressure regulator and gas bottle
together. Not all regulators fit all gas bottles.
Use only a gas hose and regulator with homologation for
the country of use.
6.2. Safety instructions
• Never connect the gas hose directly to the appliance.
Always t a pressure regulator to the gas bottle rst.
• Never modify pre-assembled or sealed parts of the gas
bottle, hose, or pressure regulator.
• Ensure as short a hose as possible (max. 1.5 m) to prevent
it being dragged over the ground.
- Never deform or fold/crease the gas hose. Check that the
hose is neither stretched nor twisted. Ensure that the hose
does not come into contact with parts that could become
www.barbecook.com
Gas bottle, hose, and
regulator
propane,
28- butane
30 mbar or their
mixtures
28-
butane
30 mbar
37 mbar propane