Technical Data; Engine; Mower; Original Spare Parts - Sabo 52-PRO S K A PLUS Betriebsanleitung

Drive speed cannot be
regulated
Extreme vibration
Cutting blade blunt.
Cut not clean,
lawn turns yellow
Cutting height too low.
Motor speed too low.
Mowing speed too high.
Insufficient overlap
between mowing lanes.
Lawn matted.
Motor speed too low.
Ejector blocked
Cutting height too low
with grass too high.
Mowing speed too fast.
Grass is damp.
Blade blunt.
Mulched grass
appearance is poor:
clumps, excessive
clippings, rough cut.
Mulching rule not
followed (cut max. 1/3 of
the grass height; the
height of the grass to be
cut must be lower than
10 cm)
Grass build-up under
deck.
Driving speed too high.
Insufficient overlapping
of cuts when mowing.
Grass not dry.
In case of faults and defects which have not been listed here, please contact the
nearest authorized dealer.
Repairs which require specialized knowledge should only be performed by a qualified
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
perform the maintenance work described here yourself.

19 TECHNICAL DATA

Engine

Engine
Engine displacement
Engine speed
Rated input
Electrode gap
Fuel
Tank contents
Have it checked by an
authorized dealer
Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorised
workshop Q .
Set higher cutting height I .
Have it checked by an
authorized dealer
Adapt mowing speed, switch
motor drive off if necessary.
If grass is long, the mowing
lanes may need to overlap
further.
A perceptible improvement
can be achieved by using a
scarifier.
Work at max. speed.
Set higher cutting height I .
Adapt mowing speed, switch
motor drive off if necessary.
Allow the lawn to dry.
Have it sharpened and
balanced by an authorized
dealer.
Adjust to higher cutting height
I .
Convert mower to side
discharge R3 and mow
grass first with higher cutting
setting.
Adjust to higher cutting height
I .
Adapt driving speed, switch
motor drive off if necessary.
Tall grass conditions may
dictate that more overlapping
of cuts is required
Adjust to higher cutting height
I .
Let grass dry.
Yamaha 4-stroke engine, MA190V
190 cm
2800 rpm
3.2 kW
0.6 - 0.7 mm
Standard unleaded fuel,
with max. 10% ethanol or max. 5% MTBE,
do not use alkylate-based petrol!
approx. 6 litres
Lubricating oil
Oil quantity

Mower

Housing
Cutting width
Cutting heights
Guide bar height adjustment
Operating speed
Weight
Length
Width
Height
Wheels front/rear
Bearings front
Bearings rear
Sound power level
Guaranteed sound power level;
measured according to 2000/14/EC
Sound pressure level
Emission sound pressure level at operator's workplace;
measured according to EN ISO 5395-2
Measuring inaccuracy; according to ISO 4871
Vibrations
Vibrations on the lawnmower's handlebar;
measured according to EN ISO 5395-2
Measuring inaccuracy; according EN 12096

20 ORIGINAL SPARE PARTS

Motor oil
Roller bearing grease
Spark plug
Air filter insert
Pre-filter
Conversion kit for mulching system
Cutter bar
3
11
SAE 10W30, SAE 10W40
4-stroke engine oil API service class SE
or a higher class oil
0.6 litres
Aluminium diecast with steel insert
500 mm
Single wheel,
25, 28, 35, 45, 55, 70, 80 mm
3-fold
2.2 – 3.7 km/h
51 kg
1,580 mm
755 mm
1,100 mm
Ø 210 mm / Ø 210 mm
Grooved ball bearing
Bronze sliding bearing
L = 96 dB(A)
wa
L = 83 dB(A)
pA
1.5 dB
a = 2.5 m/s
hW
1.3 m/s
SAE 10W30, SAE 10W40
4-stroke engine oil API service class SE
or a higher-class oil
SAA11300
SAU15939
SAU15985
SAU15986
BSA633, BSA641
For safety reasons, the cutter bar must
always be replaced by an authorised
workshop.
This workshop has the respective spare
part numbers for the cutter bar available.
2
2