Herunterladen Inhalt Inhalt Diese Seite drucken

Troubleshooting; Specifications; High Pressure Hose; A Spray Gun - Briggs & Stratton 1150 Serie Original Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 39

Troubleshooting

Problem
Pump has following problems:
failure to produce pressure,
erratic pressure, chattering,
loss of pressure, low water
volume.
Detergent fails to mix with
spray.
Engine runs good at no-load
but "bogs" when load is added.
Engine will not start; shuts
down during operation or starts
and runs rough.
For all other issues, see a Briggs & Stratton Authorized Dealer.

Specifications

Max Outlet Pressure . . 23.4 MPa (234 BAR or 3,400 PSI)*
Max Flow Rate . . . . . . . . . . . . . . . 10.6 liters/min (2.8 GPM)
Water Supply Temperature . . . . . . . . . . . 38ºC (100ºF) MAX
Displacement . . . . . . . . . . . . . . . . . . . . 250 cc (15.19 cu. in.)
Spark Plug Gap . . . . . . . . . . . . . . . . . . . 0.76 mm (0.030 in.)
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . 2.8 liters (3.0 Qt.)
Oil Capacity . . . . . . . . . . . . . . . . . . . . 0.6 liters (20 Ounces)
Sound Pressure @ 3 m . . . . . . . . . . . . . . . . . . . . . . 89 dBA §
Power Ratings: The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society
of Automotive Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance
with SAE J1995. Torque values are derived at 2600 RPM for those engines with "rpm" called out on the label and 3060
RPM for all others; horsepower values are derived at 3600 RPM. The gross power curves can be viewed at www.
BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air cleaner installed whereas gross power
values are collected without these attachments. Actual gross engine power will be higher than net engine power and is
affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide array of
products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given
piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine
components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating
conditions (temperature, humidity, altitude), and engine-to engine variability. Due to manufacturing and capacity limitations,
Briggs & Stratton may substitute an engine of higher rated power for this engine.
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard
PW101-2010 (Testing and Rating Performance of Pressure Washers).
§ Measured sound values in accordance to Tasmanian Environmental Management and Pollution Control (Miscellaneous
Noise) Regulations.
Cause
1. Low pressure spray tip installed.
2. Water inlet is blocked.
3. Inadequate water supply.
4. Inlet hose is kinked or leaking.
5. Clogged inlet hose screen.
6. Water supply is over 38°C (100°F).
7. High pressure hose is blocked or
leaks.
8. Spray gun leaks.
9. Spray tip is obstructed.
1. Detergent siphoning tube is not
submerged.
2. Detergent siphoning tube is clogged or
cracked.
3. High pressure spray tip installed.
4. Check ball stuck in detergent siphoning

system.

Engine speed is too slow.
1. Low oil level.
2. Out of fuel.
3. Spark plug wire not connected to
spark plug.
4. Flooded.
Correction
1. Replace with high pressure spray tip.
2. Clear inlet.
3. Provide adequate water flow.
4. Straighten inlet hose, patch leak.
5. Check and clean inlet hose screen.
6. Provide cooler water supply.
7. Clear blocks in outlet hose, replace
if leaking.
8. Replace spray gun.
9. Clean spray tip.
1. Insert detergent siphoning tube into
detergent.
2. Clean or replace detergent
siphoning tube.
3. Replace with black spray tip.
4. Free detergent siphoning check ball.
Move throttle control to FAST(
position.
1. Fill crankcase to proper level.
2. Fill fuel tank.
3. Connect wire to spark plug.
4. Wait 5 minutes and re-crank engine.

Service Parts

O-Ring Maintenance Kit . . . . . . . . . . . . . . . . . . . . . . . 705002
Water Inlet Screen . . . . . . . . . . . . . . . . . . . . . . . . . B2384GS
Engine Oil Bottle . . . . . . . . . . . . . . . . . . . . . . . . . . . .100005E
PumpSaver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6039
)
9

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Elite 3400Bpw3400020595-02

Inhaltsverzeichnis