Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
rope retainer 91 secure with knot as well as hang
to connecting plate 18
( 20e )
Mannually open door and mark the endposition
of top casters 90 / 105
insert track clip 89 at marked position and tighten.
Space between rearmost point to lowest point of
clip has to be equal
For door operator do not use hand rope!
Inspection instructions
For the sectional door to function properly and smoothly as well
as to ensure the maximum serviceable life, it is essential that all
parts are properly installed. In the event that the door does not
function perfectly, check the following items:
( 21 ) Are the side angle frames, the frame panels and the
horizontal track pairs horizontally, vertically and diagonally
exactly aligned and securely fastened?
( 22 ) Have all screws been securely tightened?
( 23 ) Have the vertical track pair ceiling brackets been properly
mounted?
[
]
1.30
( 24 ) Are the track joints between the angle frames and the 89°-
bends smooth and well-aligned?
( 25 ) Have the torsion springs been uniformly tightened? Check
spring tension: open door half-way. The door must rest in
this position without additional support.
( 25a )
Should the door sink or close, increase the tension
of the torsion springs.
( 25b ) Should the door open further, reduce the tension
of the torsion springs.
( 26 ) Was the door leaf properly tightened using the coupling
and torsion spring and was the second spring retightened
to compensate?
( 27 ) Are the cable windings exactly in the guides on the cable
reels? Are there at least two windings on each reel?
( 28 ) Are the centre bearings exactly aligned in order to ensure a
smooth movement of the springs?
( 29 ) Casters: Can all casters be easily turned by hand when the
door is closed?
[
1.55b
( 30 ) Has the upper caster been properly aligned and adjusted?
( 31 ) Do the caster axles protrude uniformly out of the retainers
when the garage door is open?
( 32 ) For doors with operators: was the locking mechanism
removed?
[
]
1.50db
The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!
.
[
]
1.70 a, b
. Close the door and
R/L
.
[
]
1.70 c
[
]
1.15
[
]
[
1.35
2.15]
]
Dismounting instructions for sectional doors,
types
45-4
wood
(front-mounted -VL-, rear-mounted -HL- )
- Dismounting only by qualified technicians -
Read carefully before commencing with dismounting!
You require the following tools to dismount the garage door:
Spanners or socket spanners sizes 7, 10 and 13, ratchet with
extension and sockets sizes 7, 10 and 13, Philips screw drivers
nos. 2 and 3, at least to screw clamps, eventually a hammer
and chisel.
( 33 ) Loosening torsion springs
Warning: When loosening springs wear suitable
protection and have secure footing!
Close door leaf. Insert tensioning tube in holder and loosen
screws carefully. Remove tension from torsion spring
by turning tensioning tubes in the opposite direction
indicated by the arrows. Always loosen springs from top to
bottom.
( 34 ) Remove wire cables and dismount torsion springs.
( 35 ) Secure horizontal track pairs against falling.
( 36 ) Dismount 89° bends.
( 37 ) Unscrew the horizontal track pairs brackets on the ceiling
and walls
( 38 ) Tilt horizontal track pairs, remove horizontal track pairs
from door frame.
( 39 ) Dismount anchor rails.
( 40 ) Remove horizontal track pairs from track connectors.
( 41 ) Dismount from top to bottom casters and hinges section by
section and remove each sectional leaf as disassembled.
( 42 ) Secure door frame against tipping. Loosen wall and floor
fasteners, remove door frame from garage opening and
place on garage floor. Disassemble in reverse order of
installation instructions.
Operating and Maintenance Instructions for
sectional doors,
types
45-4
wood
(front-mounted -VL-, rear-mounted -HL-)
The manufacturer's liability becomes void of any legal
substance if maintenance and operating instructions are
not properly observed and/or if non-OEM parts and
components are used, as well as any changes are made to
the door design. Whenever the door is used for commercial
purposes, please observe national and international
regulations.
Operation:
The mechanical mechanisms of this garage door have been
designed to reduce the risk of bruising, cutting and in any way
injuring persons operating or standing near the door. The
following items are essential for the safe operation of the
garage door:
Before and during door actuation ensure that no other
person is near any of the moving door parts (e. g. door leaf,
casters etc.).
For manually operated doors: open and close the door with
the external or internal handle or the service rope only.
Keep hands away from any moving parts.
Lock function
By turning the key fully in the lock it is possible to open
and close the garage door without a key.
- 10 -
with
torsion
springs
with
torsion
spring
35
R/L
Werbung
