Yamaha RX-V3900 Bedienungsanleitung Seite 84

Graphical user interface (GUI) menu
Test Tone
Use this feature to select whether to turn on or off the
test tone output while you are adjusting the tonal
quality of each speaker.
Choice
On Outputs the test tone.
Off Does not output the test tone.
2
Press 9 h to access the settings window.
PEQ Data Copy
PEQ Select
Front L
Front R
Center
3
Press 9 k / n / l / h to select "PARAM" and
then press 9 ENTER repeatedly to select a
parameter from "Band" (band), "Freq."
(frequency) or "Q" (Q factor).
y
You can adjust "Gain" (gain) with any parameter.
4
Press 9 n to select "EDIT" and press
9 ENTER to access the edit window.
For more information on the parametric equalizer and
each parameter, see page 130.
PEQ Data Copy
PEQ Select
Front L
Front R
Center
The parameter selected in "PARAM" is highlighted.
• Press 9 l / h to adjust the parameter.
• Press 9 k / n to adjust the "Gain".
• Press 9 ENTER to exit the edit window.
y
• When you select "Band" in step 3, you can use this menu
as a graphic equalizer.
• "Band #5", "Band #6", and "Band #7" can adjust the
frequencies of above 500 Hz.
• When you select "Subwoofer" in step 1 and "Band" in
step 3, you can adjust "Band #1", "Band #2", "Band #3"
and "Band #4" only. In this case, "Band #1", "Band #2",
"Band #3" and "Band #4" adjust the frequencies of below
200 Hz.
80
En
Functions
PARAM RESET
EDIT EXIT
Band / Gain
Band #1
Gain 0.0dB
Freq 62.5Hz
Q 1.000
Exit:ENTER
5
Repeat steps 3 and 4 until you are satisfied
with the results.
y
If you want to reset all "Parametric EQ" parameter settings
for the selected speaker, select "RESET" and press
9ENTER.
Select "EXIT" and press 9 ENTER to exit
6
from the settings window.
■ Tone Control (Tone control)
Use this feature to adjust the balance of bass and treble
output to your speakers or headphones.
Note
Tone Control is not effective when:
– the PURE DIRECT mode (page 47) is selected.
– MULTI CH is selected as the input source.
Control (Control mode)
Choice
Speaker
Adjust the bass/treble balance of your speakers.
Headphone Adjust the bass/treble balance of your
headphones.
y
"Speaker" and "Headphone" adjustments are stored
independently. The adjustments for "Speaker" affects the front
left/right speaker, center speaker and subwoofer channels.
Bass (Bass control)
Use this feature to adjust low-frequencies output to your
speakers or headphones.
Choices: 125 Hz, 350 Hz, 500 Hz
Control range: –6.0 dB to +6.0 dB
Initial setting: 0.0 dB
Treble (Treble control)
Use this feature to adjust high-frequencies output to your
speakers or headphones.
Choices: 2.5 kHz, 3.5 kHz, 8.0 kHz
Control range: –6.0 dB to +6.0 dB
Initial setting: 0.0 dB
Auto Bypass (Auto bypass)
Use this feature to select whether the audio output
bypasses the tone control circuitry when "Treble" and
"Bass" are set to 0 dB.
Choice
Auto
Automatically bypasses the tone control
circuitry to provide the purest signal possible
when "Treble" and "Bass" are set to 0 dB.
Off Does not bypass the tone control circuitry.
Functions
Functions