Werbung
Bedieningshandleiding
·
3
·
Plumbing
Plumbing
The Cell Vessel is designed to install in either 60 mm (2") PVC pool plumbing. The Cell Vessel must be installed on
The Cell Vessel is designed to install in either 60 mm (2") PVC pool plumbing. The Cell Vessel must be installed on
a 25 cm (10 in) run of straight pipe at the end of the return piping just before the water returns to the pool. All pool
a 25 cm (10 in) run of straight pipe at the end of the return piping just before the water returns to the pool. All pool
Leidingenwerk
equipment should be upstream from the Cell Vessel. It must be located within 4.5 meters (15 ft.) of where the
equipment should be upstream from the Cell Vessel. It must be located within 4.5 meters (15 ft.) of where the
Control Box is mounted. Also, there must be enough clearance to insert and remove the Cell from the Vessel after
Control Box is mounted. Also, there must be enough clearance to insert and remove the Cell from the Vessel after
Het celvat is ontworpen voor installatie met 60 mm (2") PVC-leidingen voor zwembaden. Het celvat moet worden geïnstalleerd op een 25 cm lange rechte pijp aan het einde van de
the Vessel is installed.
the Vessel is installed.
retourleiding, net voordat het water terugkeert naar het zwembad. Alle zwembaduitrusting moet zich stroomopwaarts van het celvat bevinden. Het moet zich binnen 4,5 meter van de
plek waar de besturingskast is gemonteerd, bevinden. Ook moet er voldoende ruimte zijn om de cel na de installatie van het celvat in en uit het vat te plaatsen en te verwijderen.
With power removed to the pump and water drained from the pool plumbing, secure the Cutting Template to the
With power removed to the pump and water drained from the pool plumbing, secure the Cutting Template to the
location where the Cell Vessel will be installed. Note that the Cutting Template is the same width as the Cell Vessel.
location where the Cell Vessel will be installed. Note that the Cutting Template is the same width as the Cell Vessel.
Nadat de pomp van de voeding is gescheiden en het water uit de leidingen van het zwembad is afgevoerd, wordt het snijsjabloon bevestigd op de plek waar het celvat zal worden
The entire Cutting Template must fit on the pipe otherwise the Cell Vessel will not fit. With the Cutting Template
The entire Cutting Template must fit on the pipe otherwise the Cell Vessel will not fit. With the Cutting Template
geïnstalleerd. Het snijsjabloon heeft dezelfde breedte als het celvat. Het volledige snijsjabloon moet op de pijp passen, anders past het celvat niet. Markeer met het sjabloon
secure on the pipe, mark 2 cutouts on to the pipe using a water pro of permanent marker.
secure on the pipe, mark 2 cutouts on to the pipe using a water pro of permanent marker.
op de buis 2 uitsparingen op de buis met behulp van een permanente waterproof marker.
Filter
Filter
Filter
Filter
pump
pump
From Pool
From Pool
Installation of Nut Assembly
Installation of Nut Assembly
Tools and spare parts(need buy separately)are necessary during installation, cutting plate , 60mm(2") fittings，2"
Tools and spare parts(need buy separately)are necessary during installation, cutting plate , 60mm(2") fittings，2"
Installatie van moereenheid
screw nuts, o-rings, etc.Refer to the diagram below.
screw nuts, o-rings, etc.Refer to the diagram below.
De hulpmiddelen en de onderdelen (apart aankopen) zijn noodzakelijk tijdens
Required for the installation
installatie, snijplaat, 60mm (2 „) montage, 2"
schroefmoeren, o-ringen, etc. Zie onderstaand schema.
Saw
⑴
⑴
·
·
⑶
⑶
Cut Pipe and Clean shavings
⑷
⑸
⑸
Slide Nuts on Pipe
Apply PVC glue on adaptor's
Apply PVC glue on adaptor's
internal face and pipe
internal face and pipe
⑹
⑺
⑺
Fix two connectors on the ends
of two pipes (press to the end)
Insert o-ring to each connector
Insert o-ring to each connector
⑻
⑼
⑼
·
Plumbing
The Cell Vessel is designed to install in either 60 mm (2") PVC pool plumbing. The Cell Vessel must be installed on
a 25 cm (10 in) run of straight pipe at the end of the return piping just before the water returns to the pool. All pool
equipment should be upstream from the Cell Vessel. It must be located within 4.5 meters (15 ft.) of where the
Control Box is mounted. Also, there must be enough clearance to insert and remove the Cell from the Vessel after
the Vessel is installed.
With power removed to the pump and water drained from the pool plumbing, secure the Cutting Template to the
location where the Cell Vessel will be installed. Note that the Cutting Template is the same width as the Cell Vessel.
The entire Cutting Template must fit on the pipe otherwise the Cell Vessel will not fit. With the Cutting Template
Solar Heater
Solar Heater
secure on the pipe, mark 2 cutouts on to the pipe using a water pro of permanent marker.
Filter
Cutting
Template
Filter
pump
From Pool
Installation of Nut Assembly
Tools and spare parts(need buy separately)are necessary during installation, cutting plate , 60mm(2") fittings，2"
Required for the installation
screw nuts, o-rings, etc.Refer to the diagram below.
Required for the installation
Hairbrush
Hairbrush
Saw
PVC glue
⑵
⑵
·
⑶
⑴
⑷
⑷
6
6
Cut Pipe and Clean shavings
⑸
⑹
⑹
⑺
⑻
⑻
⑼
⑽
⑽
·
Plumbing
The Cell Vessel is designed to install in either 60 mm (2") PVC pool plumbing. The Cell Vessel must be installed on
a 25 cm (10 in) run of straight pipe at the end of the return piping just before the water returns to the pool. All pool
equipment should be upstream from the Cell Vessel. It must be located within 4.5 meters (15 ft.) of where the
Control Box is mounted. Also, there must be enough clearance to insert and remove the Cell from the Vessel after
the Vessel is installed.
With power removed to the pump and water drained from the pool plumbing, secure the Cutting Template to the
location where the Cell Vessel will be installed. Note that the Cutting Template is the same width as the Cell Vessel.
The entire Cutting Template must fit on the pipe otherwise the Cell Vessel will not fit. With the Cutting Template
secure on the pipe, mark 2 cutouts on to the pipe using a water pro of permanent marker.
Filter
TO Pool
Solar Heater
Cutting
Template
Cutting
Template
Filter
pump
The Cutting Template is
The Cutting Template is
the same length as the
the same length as the
installed Vessel .
installed Vessel .
From Pool
Mark sure that the entire
Mark sure that the entire
Cutting Template fits at
Cutting Template fits at
the desired location .
the desired location .
Secure the Template and
Secure the Template and
mark all of the cutouts
mark all of the cutouts
Installation of Nut Assembly
Tools and spare parts(need buy separately)are necessary during installation, cutting plate , 60mm(2") fittings，2"
screw nuts, o-rings, etc.Refer to the diagram below.
Required for the installation
PVC glue
⑴
Hairbrush
PVC glue
Saw
·
⑶
⑵
Mark Pipe
Cut Pipe and Clean shavings
Cut Pipe and Clean shavings
Slide Nuts on Pipe
Slide Nuts on Pipe
⑸
6
Apply PVC glue on adaptor's
Apply PVC glue on adaptor's
internal face and pipe
internal face and pipe
Fix two connectors on the ends
Fix two connectors on the ends
of two pipes (press to the end)
of two pipes (press to the end)
⑺
Insert o-ring to each connector
Insert o-ring to each connector
Insert cell vessel and hand tighten
Insert cell vessel and hand tighten
nuts (make sure the water direction
nuts (make sure the water direction
is consistent with the arrow).
is consistent with the arrow).
⑼
4
Solar Heater
TO Pool
Cutting
TO Pool
Template
The Cutting Template is
the same length as the
installed Vessel .
Mark sure that the entire
Cutting Template fits at
the desired location .
Secure the Template and
mark all of the cutouts
·
⑶
Hairbrush
PVC glue
Saw
⑵
·
⑶
⑷
⑷
⑸
Mark Pipe
6
Mark Pipe
⑸
⑹
⑹
⑺
⑺
⑻
⑻
⑼
Insert cell vessel and hand tighten
nuts (make sure the water direction
is consistent with the arrow).
⑼
⑽
⑽
TO Pool
The Cutting Template is
the same length as the
installed Vessel .
Mark sure that the entire
Cutting Template fits at
the desired location .
Secure the Template and
mark all of the cutouts
Cut Pipe and Clean shavings
Mark Pipe
Cut Pipe and Clean shavings
Slide Nuts on Pipe
Slide Nuts on Pipe
Apply PVC glue on adaptor's
internal face and pipe
Apply PVC glue on adaptor's
internal face and pipe
Fix two connectors on the ends
Fix two connectors on the ends
of two pipes (press to the end)
of two pipes (press to the end)
Insert o-ring to each connector
Insert o-ring to each connector
Insert cell vessel and hand tighten
nuts (make sure the water direction
is consistent with the arrow).
Tighten nuts as figure shows above
⑷
⑷
⑹
⑹
⑻
⑻
⑽
⑽
7
Werbung
Kapitel
