Prior To First Use - Redmond RMC-M4510E Bedienungsanleitung

Display A2
a. Automatic programmes indicators.
b. "Time Delay" mode indicator.
c. Cooking mode indicator.
d. Timer.
e. "Keep Warm" mode indicators.
f. "EXPRESS" programme indicator.
g. Reheat mode indicator.
h. Audible signals disabled indicator.
i. Temperature value indicator.
I. PRIOR TO FIRST USE
Carefully remove the multicooker and its accessories from the packaging.
Dispose of all packaging materials.
Keep all warning labels, including the serial number identification label
located on the housing. The absence of the serial number will deprive you
of your warranty benefits!
Wipe the housing of the appliance with a soft, damp cloth. Rinse the inner
bowl with warm soapy water and dry thoroughly. An odour on first use of
the appliance is normal and does not indicate a malfunction. In such case,
clean the appliance, following "Cleaning and Maintenance".
After transportation or storage at low temperatures allow the appliance to
stay at room temperature for at least 2 hours before using.
II. MULTICOOKER OPERATION
To adjust the current time
Plug in the appliance. Press and hold "Hour/+" or "Min/–" buttons. Current time
indicator will start flashing. Use "Hour/+" button to adjust the hour value and
"Min/–" button to adjust the minute value. The hour value increases irrespective
of the minute value. After the maximum value is reached the adjustment starts
again. Press and hold the corresponding button down to scroll through the
digits. After setting is complete do not press the buttons on the panel for 5
seconds. Settings will be saved automatically.
Disabled audible signals
To disable audible signals press and hold "Menu" button in any mode. The
disabled audible signals indicator will be flashing. To enable audible signals
press and hold "Menu" button again.
To adjust cooking time
REDMOND RMC-М4510E enables to adjust cooking time for every programme,
except for "EXPRESS". Adjustment increments and range depend on the
selected programme.
After an automatic programme is selected and "Menu" button is pressed, use
the "Hour/+" button, to adjust the hour value and "Min/–" button to adjust the
minute value. The hour value changes irrespective of the minute value. After
the maximum value is reached the adjustment starts again. Press and hold
the corresponding button to scroll through the digits.
In some automatic programmes the cooking time countdown starts only
after the appliance reaches the set temperature. For example, if you pour
cold water and set "STEAM" for 5 minutes, the programme will start to
countdown only after water comes to a boil and sufficient amount of steam
is generated in the bowl. In "PASTA" the time starts to countdown after
water comes to a boil and "Start" is pressed again.
"Time Delay"
"Time Delay" function allows adjusting the time by which the dish will be
ready (including the programme time). Maximum time of delay is 24 hours.
Default time of delay comprises the programme time and the time required
to enter the operational parameters (if provided by the factory settings of
the programme). A programme can be delayed by 1 minute increments.
To adjust the time of delay after selecting of an automatic programme press
"Time Delay" button. To increase the hour value press "Hour/+" button. To
adjust the minute value press "Min/—" button. The hour value changes ir-
respective of the minute value. After the maximum value is reached the
adjustment starts again. Press and hold the corresponding button to scroll
through the digits.
Current time value is displayed during "Time Delay". To see the cooking end
time press and hold "Time Delay" button. The function is available for all
automatic programmes, except for "FRY", "PASTA " and "EXPRESS". Avoid
using "Time Delay" function for perishable meals (eggs, fresh milk, meat,
cheese, etc.).
"Keep Warm"
This function automatically activates at the end of cooking, and keeps the
food warm at 70-75°С for 12 hours. The "Keep Warm", "Cancel/Reheat" indi-
cators and direct countdown are lit on the display. To disable "Keep Warm"
press and hold "Cancel/Reheat" button.
"Keep Warm" disabled in advance
To enable "Keep Warm" function at the end of a programme is not always
desirable. REDMOND RMC-М4510E provides disabling this function in ad-
vance during "Time Delay" or the main cooking programme. To activate this
function press "Start" during cooking. To enable "Keep Warm" function press
"Start" button again.
"Keep Warm" function is not applicable for "YOGURT", "PASTA", "EXPRESS" and
"MULTICOOK" programmes with the cooking temperature set below 80°С.
Reheat
REDMOND RMC-М4510E can reheat cold dishes. To reheat a dish:
1. Fill the bowl with food and position it inside the multicooker.
2. Close the lid and plug in the appliance.
3. Press and hold "Cancel/Reheat" button. The indicators will light up
solid. The timer will start direct countdown of the reheating time.
The appliance will reheat food up to 70-75°С and will keep it warm during
12 hours. "Reheat" function can be disabled by pressing and holding "Cancel/
Reheat" button, until the indicators go out.
The "Keep Warm" and "Reheat" functions enable the appliance to maintain the
temperature of a dish for 12 hours, however it is not recommended to keep a
meal warm for more than 2-3 hours, because this may affect its flavour.
"MASTERCHIEF LITE"
Discover more possibilities for culinary creativity with the new "MASTERCHIEF
LITE" function! While "MULTICOOK" allows setting a programme parameters
before it starts, then "MASTERCHIEF LITE" allows adjustments during the
cooking process.
You can always adjust any programme, so that it corresponds to you wishes.
Does your soup boil over? Does your oatmeal "escape"? Are your vegetables
steamed for too long? Adjust the cooking temperature or time, without inter-
rupting a cooking programme as if you cook on the stove or in the oven.
You can use "MASTERCHIEF LITE" only during cooking. "MASTERCHIEF LITE"
is not applicable for "EXPRESS", "Time Delay" and waiting to access operat-
ing parameters.
When using "MASTERCHIEF LITE" the temperature can be adjusted between
35 and 170°С with 1°C increments. Possible cooking time range on the se-
lected programme with 1 minute increments.
"MASTERCHIEF LITE" can be very useful especially when you cook meals on
complex recipes, requiring combination of different cooking programmes (e.g.
cooking cabbage rolls, beef stroganoff, soup and different types of pasta, jam, etc.).
To adjust cooking temperature:
1. Press "Menu" button during cooking. The temperature value indicator
will be flashing.
2. Set the desired temperature. To increase the value press "Hour/+"
button, to reduce the value press "Min/—" button. Press and hold the
corresponding button down to scroll through the digits.
3. After the maximum (minimum) value is reached the adjustment starts
again. Do not press the buttons on the control panel for 5 seconds.
Settings will be saved automatically.
For overheat protection when setting the cooking temperature higher than
130°С the maximum programme operating time is limited to two hours
(except for "BAKE"). Cooking temperature adjustment is not applicable for
"YOGURT" programme.
To adjust cooking time:
1. Press "Menu" button twice during cooking. Time value indicator will be
flashing.
2. Set the desired cooking time. To increase the value with 1 hour incre-
ments press "Hour/+" button, to increase the value with 1 minute
increments press "Min/—" button. The hour value changes irrespective
of the minute value. After the maximum value is reached the adjust-
ment starts again. Press and hold the corresponding button to scroll
through the digits.
3. Do not press the buttons on the control panel for 5 seconds. Settings
will be saved automatically.
When setting cooking time value to 00:00, the programme operation will
be stopped.
Standard Operating Procedure for Automatic Programmes
1. Prepare (measure) the ingredients.
2. Fill the multicooker bowl with ingredients according to the cooking
programme and position it inside the appliance. Ensure that all in-
gredients are evenly spread below the maximum fill mark on the
inside of the bowl. Ensure that it has full contact with the heating
element.
3. Close the main lid until it clicks into place. Plug in the appliance.
4. Use "Menu" button to resume from standby mode. Use "Hour/+" and
"Min/–" buttons to select a programme (the corresponding programme
indicator will be flashing). Press "Menu" button again to confirm the
programme selection.
"MULTICOOK" enables to set the desired cooking temperature. Use "Hour/+"
button to increase the default value, "Min/–" button to reduce the value.
Press "Menu" button to finish the temperature setting.
5. Use "Hour/+" and "Min/–" buttons to adjust default cooking time.
6. Set time of delay if necessary.
RMC-M4510E GBR
7