Philips Respironics AF811 Gebrauchsanweisung Seite 3

Removing the CapStrap Headgear
First, undo the bottom swivel clips by pulling the ball out
and away from the socket (Figure 3). Next, gently twist
the CapStrap hook (I) so that it disconnects from the
forehead support bracket.
Replacing the CapStrap Headgear
Press the CapStrap hook (I) into the back of the slot on the forehead
support bracket and press until they snap together (Figure 4). On the
lower straps, press the balls of the swivel clips into the sockets on the
faceplate.
Removing the Four Point Headstrap
First, undo the bottom swivel clips by pulling the ball
out and away from the socket. Next, open the headgear
tabs and pull them out of the slots on the forehead support arm.
Replacing the Four Point Headstrap
On the top strap, thread the headgear tabs through the slots in the
forehead support arm (Figure 5). Fold the tabs back so that they catch
onto the headgear straps. On the lower straps, press the
balls of the swivel clips into the sockets on the faceplate.
Patient Access and Removing the Mask
Disconnect the bottom strap swivel clips and swing the mask
upward (Figure 6). This allows easy access to the patient. To remove
completely, disconnect the bottom strap swivel clips and pull the entire
assembly over the patient's head.
If using the Four Point Headstrap, disconnect the bottom strap swivel
clips and pull the entire assembly off over the patient's head.
Cushion and Flap Assembly
This mask is intended for single patient use and is fully assembled and
ready to use. Place the gel cushion onto the faceplate (Figure 7). Then
place the flap over the gel cushion and push the retaining ring onto
the faceplate until the connection tabs click into place. Tug on the
cushion to make sure all of the parts are securely in
place.
Reorder Numbers
1063015 Respironics AF811 Mask w/ CapStrap Headgear, L, 1 EA
1063016 Respironics AF811 Mask w/ CapStrap Headgear, M, 1 EA
1063047 Respironics AF811 Mask w/ CapStrap Headgear, S, 1 EA
1063051 Respironics AF811 Mask w/ CapStrap Headgear, L, 5 PK
1063052 Respironics AF811 Mask w/ CapStrap Headgear, M, 5 PK
1063053 Respironics AF811 Mask w/ CapStrap Headgear, S, 5 PK
1019547 Respironics CapStrap Headgear Only, 5 PK
1015788 Respironics Four Point Headgear w/ Swivel Clips, 1 EA
452040 NG Tube Sealing Pad, 10 PK
4
Figure 3
I
Figure 4
Figure 5
Figure 6
Figure 7
Specifications
Warning: The technical specifications of the mask are provided for your healthcare
professional to determine if it is compatible with your CPAP or bi-level therapy device. If
used outside these specifications, or if used with incompatible devices, the mask may be
uncomfortable, the seal of the mask may not be effective, optimum therapy may not be
achieved, and leak, or variation in the rate of leak, may affect device function.
Intentional Leak
Pressure Flow Curve
AF811 with Whisper Swivel II
AF811 with Disposable Exhalation Port (DEP)
90
80
70
60
50
40
30
20
10
0
0 5 10 15
Pressure cm H
Pressure Drop cm H O (hPa)
2
50 SLPM 100 SLPM
All mask sizes: 0.4 1.0
Deadspace
Small 260 mL
Medium 280 mL
Large 300 mL
Disposal
Dispose of in accordance with local regulations.
Storage Conditions
Temperature: -4° F to +140° F (-20° C to +60° C)
Relative Humidity: 15% to 95%, non-condensing
Murrysville, PA 15668 USA
20 25 30
O
2
AUSTRALIAN SPONSOR DETAILS:
Philips Electronics Australia Ltd.
65 Epping Road, North Ryde, NSW 2113
Australia
© 2014 Koninklijke Philips N.V. All rights reserved.
1071654 R06
5
LZ 4/30/2014