Siemens 840D sl Handbuch Seite 12

Inhaltsverzeichnis
8.3.4 Konturelemente erstellen .......................................................................................................... 342
8.3.5 Kontur ändern ........................................................................................................................... 347
8.3.6 Konturaufruf (CYCLE62) - nur bei G-Code-Programm............................................................. 348
8.3.7 Bahnfräsen (CYCLE72) ............................................................................................................ 349
8.3.8 Konturtasche/Konturzapfen (CYCLE63/64) .............................................................................. 353
8.3.9 Konturtasche vorbohren (CYCLE64) ........................................................................................ 354
8.3.10 Konturtasche fräsen (CYCLE63) .............................................................................................. 357
8.3.11 Konturtasche Restmaterial (CYCLE63) .................................................................................... 360
8.3.12 Konturzapfen fräsen (CYCLE63) .............................................................................................. 362
8.3.13 Konturzapfen Restmaterial (CYCLE63) .................................................................................... 364
8.4 Drehen - nur bei G-Code-Programmen .................................................................................... 366
8.4.1 Allgemeines............................................................................................................................... 366
8.4.2 Abspanen (CYCLE951)............................................................................................................. 366
8.4.3 Einstich (CYCLE930) ................................................................................................................ 369
8.4.4 Freistich Form E und F (CYCLE940) ........................................................................................ 371
8.4.5 Freistich Gewinde (CYCLE940)................................................................................................ 373
8.4.6 Gewindedrehen (CYCLE99) ..................................................................................................... 376
8.4.7 Gewindekette (CYCLE98)......................................................................................................... 384
8.4.8 Abstich (CYCLE92) ................................................................................................................... 387
8.5 Konturdrehen - nur bei G-Code-Programmen .......................................................................... 389
8.5.1 Allgemeines............................................................................................................................... 389
8.5.2 Darstellung der Kontur .............................................................................................................. 390
8.5.3 Neue Kontur anlegen ................................................................................................................ 391
8.5.4 Konturelemente erstellen .......................................................................................................... 392
8.5.5 Kontur ändern ........................................................................................................................... 398
8.5.6 Konturaufruf (CYCLE62) ........................................................................................................... 399
8.5.7 Abspanen (CYCLE952)............................................................................................................. 400
8.5.8 Abspanen Rest (CYCLE952) .................................................................................................... 405
8.5.9 Stechen (CYCLE952)................................................................................................................ 407
8.5.10 Stechen Rest (CYCLE952) ....................................................................................................... 409
8.5.11 Stechdrehen (CYCLE952) ........................................................................................................ 411
8.5.12 Stechdrehen Rest (CYCLE952)................................................................................................ 414
Weitere Zyklen und Funktionen ................................................................................................ 416
8.6
8.6.1 Schwenken Ebene/Werkzeug (CYCLE800) ............................................................................. 416
8.6.2 Schwenken Werkzeug (CYCLE800)......................................................................................... 424
8.6.2.1 Schwenken Werkzeug/Anstellen von Fräswerkzeugen - nur bei G-Code-Programm
(CYCLE800).............................................................................................................................. 424
8.6.2.2 Schwenken Werkzeug/Ausrichten von Fräswerkzeugen - nur bei G-Code-Programm
(CYCLE800).............................................................................................................................. 425
8.6.3 High Speed Settings (CYCLE832)............................................................................................ 426
8.6.4 Unterprogramme ....................................................................................................................... 428
8.7 Weitere Zyklen und Funktionen ShopMill ................................................................................. 430
8.7.1 Transformationen ...................................................................................................................... 430
8.7.2 Verschiebung ............................................................................................................................ 431
8.7.3 Rotation ..................................................................................................................................... 432
8.7.4 Skalierung ................................................................................................................................. 433
8.7.5 Spiegelung ................................................................................................................................ 433
8.7.6 Gerade oder kreisförmige Bearbeitungen................................................................................. 434
8.7.7 Gerade programmieren............................................................................................................. 436
8.7.8 Kreis mit bekanntem Mittelpunkt programmieren ..................................................................... 437
8.7.9 Kreis mit bekanntem Radius programmieren............................................................................ 438
8.7.10 Helix .......................................................................................................................................... 439
8.7.11 Polarkoordinaten ....................................................................................................................... 440
12
Bedienhandbuch, 07/2010, 6FC5398-7CP40-0AA0
Fräsen