Siemens 840D sl Handbuch Seite 11

7.9 Nullpunktverschiebungen aufrufen ............................................................................................240
7.10 Programmsätze wiederholen .....................................................................................................241
7.11 Stückzahl angeben ....................................................................................................................243
7.12 Programmsätze ändern .............................................................................................................244
7.13 Programmeinstellungen ändern.................................................................................................245
7.14 Auswahl der Zyklen über Softkey ..............................................................................................246
7.15 Technologische Funktionen aufrufen.........................................................................................251
7.15.1 Weitere Funktionen in den Eingabemasken ..............................................................................251
7.15.2 Überprüfung von Eingabeparametern .......................................................................................251
7.15.3 Einstelldaten für Technologische Funktionen ............................................................................252
7.15.4 Zyklenaufruf ändern ...................................................................................................................252
7.16 Messzyklenunterstützung ..........................................................................................................253
7.17 Beispiel Standardbearbeitung....................................................................................................255
7.17.1 Werkstückzeichnung..................................................................................................................256
7.17.2 Programmierung ........................................................................................................................256
7.17.3 Ergebnisse/Simulationstest........................................................................................................268
7.17.4 G-Code-Bearbeitungsprogramm................................................................................................269
8 Technologische Funktionen programmieren (Zyklen) ............................................................................ 273
8.1 Bohren........................................................................................................................................273
8.1.1 Allgemeines................................................................................................................................273
8.1.2 Zentrieren (CYCLE81) ...............................................................................................................274
8.1.3 Bohren (CYCLE82) ....................................................................................................................276
8.1.4 Reiben (CYCLE85) ....................................................................................................................277
8.1.5 Tieflochbohren (CYCLE83)........................................................................................................278
8.1.6 Ausdrehen (CYCLE86) ..............................................................................................................281
8.1.7 Gewindebohren (CYCLE84, 840) ..............................................................................................284
8.1.8 Bohrgewindefräsen (CYCLE78).................................................................................................288
8.1.9 Positionen und Positionsmuster.................................................................................................291
8.1.10 Beliebige Positionen (CYCLE802) .............................................................................................293
8.1.11 Positionsmuster Linie (HOLES1), Gitter oder Rahmen (CYCLE801)........................................294
8.1.12 Positionsmuster Kreis (HOLES2)...............................................................................................295
8.1.13 Positionen wiederholen..............................................................................................................296
8.2 Fräsen ........................................................................................................................................298
8.2.1 Planfräsen (CYCLE61) ..............................................................................................................298
8.2.2 Rechtecktasche (POCKET3) .....................................................................................................301
8.2.3 Kreistasche (POCKET4) ............................................................................................................304
8.2.4 Rechteckzapfen (CYCLE76)......................................................................................................309
8.2.5 Kreiszapfen (CYCLE77).............................................................................................................311
8.2.6 Mehrkant (CYCLE79).................................................................................................................313
8.2.7 Längsnut (SLOT1) .....................................................................................................................316
8.2.8 Kreisnut (SLOT2) .......................................................................................................................319
8.2.9 Offene Nut (CYCLE899) ............................................................................................................322
8.2.10 Langloch (LONGHOLE) - nur für G-Code Programme..............................................................328
8.2.11 Gewindefräsen (CYCLE70) .......................................................................................................330
8.2.12 Gravur (CYCLE60).....................................................................................................................333
8.3 Konturfräsen...............................................................................................................................339
8.3.1 Allgemeines................................................................................................................................339
8.3.2 Darstellung der Kontur ...............................................................................................................339
8.3.3 Neue Kontur anlegen .................................................................................................................340
Fräsen
Bedienhandbuch, 07/2010, 6FC5398-7CP40-0AA0
Inhaltsverzeichnis
11