Technical Data; Noise/Vibration Information; Delivery Scope - Bosch GCM 8 SDE Professional Originalbetriebsanleitung

OBJ_BUCH-2303-005.book Page 29 Thursday, December 15, 2016 11:35 AM
49 Clamping flange
50 Interior clamping flange
51 SDS bolt
52 Threaded rod
53 Exit opening for laser beam
54 Screws for insert plate
55 Lock screw of the material stop*
56 Clamping screw of the material stop*
57 Adjustment screw for laser position
(parallelism)

Technical Data

Sliding Mitre Saw
Article number
3 601 M19 ...
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Divergence of laser line
Weight according to EPTA-Procedure 01:2014
Protection class
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Max. cutting width
Mounting hole diameter
Permissible workpiece dimensions (maximum/minimum) see page 33.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may
Bosch Power Tools
58 Stop screw for 0° bevel angle
59 Screw for bevel angle indicator
60 Stop screw for left-hand bevel angle range
61 Stop screw for right-hand bevel angle range
62 Set screws of scale 18 for mitre angles
63 Screw for mitre angle indicator
64 Velcro strap
65 Laser lens cover
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
W
-1
min 3500–5000
nm
mW
mrad (full angle)
kg
mm
mm 1.3–1.8
mm
mm
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.

Delivery Scope

Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Material clamp 29
– Hex key 36
– SDS bolt 51
English | 29
GCM 8 SDE
... 2.. ... 2B.
1600 1400
3500–5000
 
650 650
< 0.39 < 0.39
1M 1M
1.0 1.0
18.9 18.9
/II /II
216 216
1.3–1.8
3.3 3.3
30 25.4
1 609 92A 34B | (15.12.16)