Assembly; Charging The Batteries Of The Measuring Tool And; Laser Receiver (See Figures A - B); Charge-Control Indicator - Bosch GRL Professional 500 H Originalbetriebsanleitung

Laser Receiver/Remote Control
Article number
Receivable wavelength
1) 2)
Working range (radius)
– Laser Receiver with Rotational Laser
Level
– Remote Control
Receiving angle
3)
Measuring accuracy
– Setting "fine "
– Setting "medium "
– Setting "coarse "
Display size
Reception area
Operating temperature
Storage temperature
Relative air humidity, max.
Max. altitude
Activation setting for sleep mode
– After 30 mins without button press
– After 30 mins without any laser de-
tection
Theft alarm system
Calibration interval indicator
Weight according to
EPTA-Procedure 01/2003
Dimensions (length x width x height)
Degree of protection
Battery
Rated voltage
Capacity
Number of battery cells
Operating time, approx.
1) The working range (radius) can be reduced due to unfavourable
ambient conditions (e.g. direct sunlight).
2) depends on clearance between laser receiver and rotational laser
level
3) at a distance of 30 m
The serial number 27 on the type plate is used to clearly identify your
laser receiver/remote control.
Bosch Power Tools
LR 50 Battery Charger
3 601 K69 A.. Article number
625–645 nm Charging time
Output voltage
Charging current
250 m
Protection class
150 m

Assembly

70° (±35°)

Charging the Batteries of the Measuring Tool and

±1 mm
Laser Receiver (see figures A – B)
±2 mm
 Do not use a different battery charger. The battery
±3 mm
±5 mm
±7 mm
 Observe the mains voltage! The voltage of the power
±10 mm
62 x 31 mm
100 x 18 mm
–10 °C ... +50 °C
door areas. The charging cable is not permitted for charging
–20 °C ... +70 °C
outdoors or in moist environments.
90 %
Note: The batteries of the measuring tool and laser receiver
2000 m
are supplied partially charged. To ensure full capacity of the
batteries, completely charge the batteries before the first

use.
The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure
0–150 m
does not damage the battery.


Charge-control Indicator

The measuring tool must be switched on (see "Switching On",
0.3 kg
page 37) to display the battery charge status of the measur-
152 x 77 x 32 mm
ing tool and laser receiver.
IP 56 (protected
Display
against dust and
powerful water jets) Indications
Li-Ion
29
7.4 V
30
1 Ah
2
29
25 h
30
29
30
29
30
29
30
If the measuring tool is switched off and the laser receiver is in
the charging/storage station 6, the battery charge status can
be displayed as follows:
charger provided is matched to the lithium-ion battery in-
stalled in your measuring tool.
source must correspond with the data on the type plate of
the battery charger.
The measuring tool and laser receiv-
er must be charged only in dry in-
Meaning
Battery fully
charged.
Battery partially
charged.
Battery partially
charged.
Battery partially
charged.
Battery should
be recharged.
English | 35
2 610 A16 4..
approx.3 h
12 V
5 A
/II
Remaining
Capacity measuring
time, approx.
60–100 % 15–25 h
40–60 % 10–15 h
20–40 % 5–10 h
10–20 % 2,5–5 h
0–10 % 0–2,5 h
2 610 031 676 | (15.7.14)