Setting The Time Data; Setting The User Bits; Setting The Time Code - Sony DNV-5 Bedienungsanleitung

5-2 Setting the Time Data

5-2-1 Setting the User Bits

By setting the user bits (up to 8 hexadecimal digits),
you can record user information such as the date, time,
or scene number on the time code track.
When it is necessary to record more detailed
information, you can record it as shot data.
For more information about shot data, see Section 5-5
"VTR Menu Display in the Display Panel" (page 5-12(E)).
Follow the procedure below to set the user bits.
CTL TC DATA
HOLD RESET DISPLAY
DIAG PB VITC NDF EXT-LK HOLD
00:00:00:00 V
H
H MIN SEC FRM
p p p p p p p
TAPE E B
E p p p p p p p
BATT F
RF SERVO HUMID SLACK
ADVANCE SHIFT
PRESET
F-RUN 0
REGEN SET
R-RUN
CLOCK
DATA CH-1
DIAG
DISPLAY
U-BIT
NTSC
TIME
SHOT
PAL
NO.
Setting the user bits
1
Set the DISPLAY switch to DATA.
2
Set the DATA DISPLAY switch to U-BIT.
3
Set the F-RUN/SET/R-RUN switch to SET.
4
Set the user bits, using the SHIFT and ADVANCE
buttons.
SHIFT: Selects a digit to set. Each time you press
it, the flashing digit moves one to the right.
Pressing this button while holding down the
HOLD button moves the flashing digit one to
the left.
ADVANCE: Increments the value of the flashing
digit.
Pressing this button while holding down the
HOLD button decrements the value of the
flashing digit.
Hexadecimal digits A to F are displayed as follows:
Hexadecimal A B
A b
Display
5-2(E)
Chapter 5 Adjustments and Settings for Recording
1
OFF ON
LCD LIGHT WARNING
OVER EMPH OVER
0
10
20
30
40
∞
1 2
PEAK dB
4
LEVEL
3,5
10 0 10
AUTO
MANUAL
AUDIO SELECT
CH-2
2
AUDIO IN
FRONT
REAR
WIRELESS
C D E F
C d E F
5
Set the F-RUN/SET/R-RUN switch to F-RUN or
R-RUN depending on whether to advance the time
code constantly or only during recording.
The specified user bits will be recorded in the LTC
and VITC.
Storing the user bits in memory
The user bits setting (apart from the real time) is stored
in memory when the power is turned off.

5-2-2 Setting the Time Code

The time code setting range is from 00 : 00 : 00 : 00 to
23 : 59 : 59 : 29 (hour : minute : second : frame) for
NTSC systems, or to 23 : 59 : 59 : 24 for PAL systems.
Follow the procedure below to set the time code.
CTL TC DATA
HOLD RESET DISPLAY
DIAG PB VITC NDF EXT-LK HOLD
00:00:00:00
H
H MIN SEC FRM
p p p p p p p
TAPE E B
E p p p p p p p
BATT F
RF SERVO HUMID SLACK
ADVANCE SHIFT
PRESET
F-RUN 0
REGEN
SET
R-RUN
CLOCK
DATA CH-1
DIAG
DISPLAY
U-BIT
NTSC
TIME
SHOT
PAL
NO.
Setting the time code
1
Set the DISPLAY switch to TC.
2
Set the PRESET/REGEN/CLOCK switch to
PRESET.
3
Set the F-RUN/SET/R-RUN switch to SET.
4
Using the SHIFT and ADVANCE buttons, set the
time code.
SHIFT: Selects a digit to set. Each time you press
it, the flashing digit moves one to the right.
Pressing this button while holding down the
HOLD button moves the flashing digit one to
the left.
1
OFF ON
LCD LIGHT WARNING
OVER EMPH OVER
0
V
10
20
30
40
∞
1 2
PEAK dB
4
LEVEL
3,5
10 0 10
AUTO
MANUAL
AUDIO SELECT
2
CH-2
AUDIO IN
FRONT
REAR
WIRELESS