GRAPHITE 59G220 Bedienungsanleitung Seite 11

An angle grinder is a hand-held power tool with class II insulation. The
device is driven by a single-phase commutator motor, whose rotational
speed is reduced by means of a toothed angular gear. It can be used
for both grinding and cutting. This type of power tool is widely used for
removing all types of burrs from the surfaces of metal elements,
surface treatment of welds, cutting thin-walled pipes and small metal
elements, etc. With the appropriate accessories, an angle grinder can
be used not only for cutting and grinding, but also for cleaning, e.g.
rust, paint coatings, etc.
Its areas of application include broadly understood repair and
construction work, not only related to metals. An angle grinder can
also be used for cutting and grinding building materials, e.g. bricks,
paving stones, ceramic tiles, etc.
The device is intended for dry use only and is not suitable for
polishing. Do not use the power tool for purposes other than those
for which it is intended.
Improper use.
• Do not process materials containing asbestos. Asbestos is
carcinogenic.
• Do not process materials whose dust is highly flammable or
explosive. When working with power tools, sparks are generated
which may ignite the vapours emitted.
• Do not use cutting discs for grinding work. Cutting discs work
with their side surface, and grinding with the front surface of such
a disc may damage it, resulting in personal injury to the operator.
DESCRIPTION OF GRAPHIC PAGES
The numbering below refers to the components of the device shown
on the graphic pages of this manual.
1. Spindle lock button
2. Switch
3. Auxiliary handle
4. Disc guard
5. Outer flange
6. Internal flange
7. Switch lock button
8. Carbon brush cover
9. Main handle lock
10. Lever (disc guard)
11.Speed control knob
12.Key
* There may be differences between the drawing and the product.
ACCESSORIES
• Disc guard
• Special wrench
• Additional handle
PREPARATION FOR WORK
INSTALLATION OF THE ADDITIONAL HANDLE
The additional handle (3) is installed in one of the holes on the grinder
head. It is recommended to use the grinder with the additional handle.
If you hold the grinder with both hands during operation (also using the
additional handle), there is less risk of touching the rotating disc or
brush with your hand and suffering injury during recoil.
ADJUSTABLE MAIN HANDLE
Before starting work, you can adjust the position of the main handle of
the grinder so that it is most convenient for the work being performed.
The handle can be set in 3 positions by turning it
from the basic position.
• Press the main handle lock button (9) (Fig. D).
• Turn the main handle to the desired position.
• The main handle will automatically lock in the selected position.
INSTALLATION AND ADJUSTMENT OF THE DISC GUARD
The blade guard protects the operator from debris, accidental contact
with the working tool or sparks. It should always be fitted, taking extra
care to ensure that the covering part faces the operator.
The design of the blade guard mounting allows the guard to be
adjusted to the optimum position without tools.
• Loosen and pull back the lever (10) on the blade guard (4).
• Turn the blade guard (4) to the desired position.
• Lock by lowering the lever (10).
Removal and adjustment of the blade guard is carried out in the
reverse order to its installation.
REPLACEMENT OF WORK TOOLS
Wear work gloves when replacing working tools.
The spindle lock button (1) is used only to lock the grinder spindle
during installation or removal of the working tool. Do not use it as a
brake button while the disc is spinning. Doing so may damage the
grinder or injure the user.
INSTALLING DISCS
For grinding or cutting discs with a thickness of less than 3 mm, the
outer flange nut (5) must be screwed on with the flat surface facing the
disc (Fig. B).
• Press the spindle lock button (1).
• Insert the special key (included) into the holes in the outer flange
• Turn the key to loosen and remove the outer flange (5).
• Place the disc so that it is pressed against the surface of the
• Screw on the outer flange (5) and tighten slightly with the special
The discs are removed in the reverse order to installation. During
installation, the disc should be pressed against the surface of the inner
flange (6) and centred on its chamfer.
INSTALLATION OF WORK TOOLS WITH A
• Press the spindle lock button (1).
• Remove the previously mounted working tool, if any.
• Before installation, remove both flanges – the inner flange
• (6) and the outer flange (5).
• • Screw the threaded part of the working tool onto the spindle
The removal of working tools with a threaded hole is carried out in the
reverse order to installation.
MOUNTING THE ANGLE GRINDER IN THE ANGLE GRINDER
STAND
The angle grinder may be used in a dedicated angle grinder stand,
provided that it is correctly mounted in accordance with the stand
manufacturer's assembly instructions.
OPERATION / SETTINGS
Before using the grinder, check the condition of the grinding wheel. Do
- 1 piece not use chipped, cracked or otherwise damaged grinding wheels.
- 1 pc.
Replace a worn disc or brush with a new one immediately before use.
- 1 pc.
After finishing work, always switch off the grinder and wait until the
working tool has come to a complete stop. Only then can the grinder
be put away. Do not slow down the rotating grinding wheel by pressing
it against the workpiece.
• Never overload the grinder. The weight of the power tool exerts
• If the grinder falls during operation, it is essential to check and,
• Never strike the workpiece with the tool.
• Avoid bouncing the blade and scraping material with it,
90°
to the left or right
Never use discs designed for cutting wood from circular saws.
The use of such discs often results in kickback of the power tool,
loss of control and may lead to injury to the operator.
TURNING ON/OFF
Hold the sander with both hands during start-up and
operation. The sander is equipped with a safety switch to prevent
accidental start-up.
• Press the safety button (7).
• Press the switch button (2) (Fig. C).
• Releasing the pressure on the switch button (2) stops the
11
(5) (Fig. A).
inner flange (6).
key.
and tighten it slightly.
sufficient pressure to work effectively. Overloading and
excessive pressure can cause dangerous breakage of the
working tool.
if necessary, replace the working tool if it is found to be damaged
or deformed.
especially when working on corners, sharp edges, etc. (this may
cause loss of control of the power tool and kickback).
grinder.
THREADED
HOLE