GRAPHITE 58G017 Übersetzung Der Originalanleitung Seite 8

CAUTION: This appliance is intended for indoor use.
Despite the inherently safe design, the use of safety measures
and additional protective measures, there is always a risk of
residual injury during operation.
Li-Ion batteries can leak, catch fire or explode if they are heated
to high temperatures or short-circuited. Do not store them in the
car during hot and sunny days. Do not open the battery pack. Li-
Ion batteries contain electronic safety devices which, if
damaged, can cause the battery to catch fire or explode.
EXPLANATION OF THE PICTOGRAMS USED
1.CAUTION: Take special precautions.
2.Read the operating instructions, observe the warnings and safety
conditions contained therein!
3.Wear personal protective equipment (safety goggles, ear
defenders).
4.Use a dust mask!
5.Use protective gloves.
6.Keep children away from the tool.
7.Use protective clothing.
8.Protect the unit from moisture.
9.Remove the battery from the unit before adjusting or cleaning.
10.The device is designed for indoor operation.
11.Maximum permissible cell temperature 45°C.
12.Do not throw cells into fire.
13.Recycling.
14.Third class protection of the charger.
15.Do not throw the cells into water.
16. EAC certification mark.
17. Ukrainian market certification mark.
CONSTRUCTION AND USE
The sabre saw is a battery powered power tool. It is driven by a DC
commutator motor whose speed has been converted into a
reciprocating motion. The machine is designed for making straight
split cuts, curved cuts and notches in wood, wood-based materials
and plastics and metals (provided a suitable blade is used). Areas of
use are carrying out repair and construction work as well as any work
in the field of independent amateur activity (DIY).
Do not misuse the power tool.
DESCRIPTION OF THE GRAPHIC PAGES
The following numbering refers to the components of the tool shown
on the graphic pages of this manual.
1.Blade
2.Foot
3.Quick-mounting lever for saw blade
4.Front handle
5.Switch lock button
6.Switch
7.Main handle
8.Battery pack clamp button
9.Battery pack (not included)
10.LED light
11.Charger (not supplied)
12.Battery charge status indicator button
13.Battery charge status indication (LEDs)
* Differences between illustration and product may occur.
ACCESSORIES AND EQUIPMENT
Blade
PREPARATION FOR WORK
REMOVING/INSERTING THE BATTERY PACK
- Press the battery clamping button (8) and pull out the battery pack
(9) (Fig. A).
• Insert the charged battery pack (9) into the handle holder until the
battery pack fixing button (8) audibly engages.
Battery types and capacities
The unit is suitable for use with ENERGY+ batteries 58G001, 58G001-
1, 58G004. 58G004-1, 58G086, 58G086-1, 58GE152.
We recommend the 4 Ah battery 58G004-1
Battery type
Battery capacity
Operating/performance
time
CHARGING THE BATTERY PACK
Battery charging should be carried out in conditions where the
ambient temperature is 4
not been used for a long period of time will reach full power capability
after approximately 3 - 5 charge and discharge cycles.
• Remove the battery pack (9) from the unit (Fig. A).
• Plug the charger (11) into the mains socket (230 V AC).
• Insert the battery pack (9) into the charger (11) (fig. B).Check that
the battery pack is properly seated (inserted all the way).
When the charger is plugged into the mains socket (230 V AC), the
green LED (10) on the charger will illuminate to indicate that the
voltage is connected.
When the battery pack (9) is placed in the charger (11), the red LED
(10) on the charger lights up to indicate that the battery is being
charged.
At the same time, the green charging status LEDs (13) on the battery
pack (13) flash in a different pattern (see description below).
• Pulsating light of all LEDs - indicates that the battery is
exhausted and needs to be recharged.
• Pulsating light of 2 diodes - indicates partial discharge.
• Pulsating of 1 diode - indicates high battery charge.
When the battery is charged, the LED (10) on the charger lights up
green and all the LEDs of the battery charge status (13) light up
continuously. After a certain time (approx. 15s), the battery charge
status LEDs (13) go out.
The battery should not be charged for longer than 8 hours.
Exceeding this time may damage the battery cells. The charger
will not switch off automatically when the battery is fully
charged. The green LED on the charger will remain lit. The
battery charge status LED will turn off after a period of time.
8
58G001 58G004 58G086
58G001- 58G004- 58G086-
1 1 1
2 Ah 4 Ah 6 Ah
38 min 80 min 97 min
0 (0) C
C - 40 . A new battery or one that has
- 1 pc.
58GE152
8 Ah
170 min