Memory Function In Auto Mode - Royal Catering Rcbm-30In Bedienungsanleitung

EN
The factory settings of the device are such that step
3 is the BOILING procedure and it is the last step of
the entire process – once boiling is over the device
will stop working. If any additional steps are required
between step 2 and the boiling step, then change
the temperature setting in step 3 and configure
one of the subsequent steps as the boiling process.
Remember for the temperature ins subsequent
steps to be higher than in the preceding step. In the
BOILING stage, POWER and TIMER may also be set.
The default temperature is set to 100°C. After setting
the power and timer press AUTO – the devise will
switch to hop adding reminder mode – described in
section 9 below.
4. Once all the needed steps have been configured (as
required – up to 9 steps), press the START button to
confirm all settings. The device will start with R0S1,
the first configured step. R0S1 will flash on the display
during that time and the device will heat up the water
to the temperature set for that step (R0S1). Once the
pre-set temperature has been reached, an acoustic
signal will sound, R0S1 and MASHING will flash on
the display – this is a reminder to add ingredients.
Once the ingredients have been added, press AUTO
and the device will continue with step R0S1 – heating
at a pre-set temperature and for a pre-set time. Once
step R0S1 ends, the device will move onto the next
step – R0S2 and so on until the last configured step
which should entail BOILING.
5. Only one boiling process may be programmed –
once complete no more steps will be performed. The
boiling POWER can be set during operation.
6. When the R0S1 step is completed, the device will
sound a reminder. The program will not go to the
next step until the AUTO button is pressed. This is a
reminder to add ingredients.
7. The reminder in the BOILING step works on a similar
principle to the reminder to add ingredients. Once
the device ends the step before boiling – an acoustic
signal will sound. Press the AUTO button to confirm
start of the boiling step. This is a reminder for spraying
(sparging).
8. The PAUSE button will stop the device and timer.
Now the parameters can be adjusted. Press the AUTO
button again to continue operation.
9. To skip the current step in auto mode and go to the
next step press the START button.
10. To set a reminder to add hops during the boiling
process: during step R0S3 (BOILING) (according to
factory settings, step R0S3 is pre-set as the boiling
step, but any other out of the 9 available steps can
be configured as boiling) a reminder to ass hops
may be configured (and also its boiling time) – once
the heating power and boiling time on step R0S3
(BOILING) have been set, „HOP 1" will be shown on
the display and a flashing time value. Use – or +
buttons to set the time. In order to add further hop
reminders, press the TIMER button – 9 such reminders
can be set, however remember that the boiling time
(BOILING) has to be longer than the first hop boiling
time (HOP1), and the first hop boiling time (HOP1)
has to be longer than the second hop boiling time
(HOP2) and so on. Therefore, boiling time (BOILING)
> hop boiling time HOP1 >hop boiling time HOP2
> hop boiling time HOP3 > hop boiling time HOP4
12
> hop boiling time HOP5 > hop boiling time HOP6
> hop boiling time HOP7 > hop boiling time HOP8
> hop boiling time HOP9. Press the START button to
begin heating.
11. Press and hold the POWER and TIMER buttons
for 5 seconds with the display empty to switch to
recipe selection mode. Press „-" or „+" to choose
the required recipe. Up to 10 recipes may be pre-
programmed. Press the Start button to select the
chosen recipe, the display will be empty, then press
the AUTO/PAUSE button to enter recipe edition mode.
Press the START button to begin the selected recipe
immediately or press the AUTO/PAUSE button to edit
or check the pre-set programme step-by-step.
12. Press the STOP button to skip all steps and the device
will turn off, END will be displayed and a bell will
sound for 30s. Press the STOP button again to go into
stand-by mode (empty display).

6.4. MEMORY FUNCTION IN AUTO MODE

1. Once all parameters have been set in Auto mode,
press the STOP button until the display is empty. Do
not turn the device off! Follow the step below to save
a programme.
2. Press the MANUAL button to enter manual editing
mode, then press and hold the MANUAL button for 5
seconds. This will store the last settings to the memory
both in manual and auto mode. A bell will sound to
confirm that the programme has been saved.
3. Turn the device off and on, then press the AUTO
button and step one from the most recently selected
programme will appear on the display.
4. Press the START button to activate the device.
5. This device does not remember programmes
in batches. Each save has to be performed in
accordance with the steps described above.
Press AUTO/PAUSE to edit a recipe.
Temp/Power/Timer may be set.
Press START (not applicable
Press AUTO again
to the BOILING step), and
to edit/check the
the device will begin the
next step.
heating up process. RXSX in
top right corner of the display
Press AUTO during
will begin flashing when the
boiling to set the
hops reminder.
If you want to skip the
Press „-" or „+" to set the first
hop reminder, press
reminder (Timer) to add hops.
START once again –
Then press the TIMER button to
the device will start
set the second hop reminder.
heating up.
Press the Timer button again
for the third, fourth, fifth... ninth
reminder.
should be set so that the time
for the first reminder is shorter
than the boiling time but longer
that the second reminder time,
the second longer than the third,
and so on: BOILING>HOP1>
HOP2> HOP3> HOP4> HOP5>
HOP6> HOP7> HOP8> HOP9
Press the START button to
device is in use.
Given reminders
begin heating.