Operating And Safety Instructions; Warranty And Disclaimer - BWT AQA drink 1 CAS Bedienungsanleitung

6. OPERATING AND SAFETY
INSTRUCTIONS
These installation and operation instructions
contain important information concerning the
safe and efficient use of the AQA drink 1 CAS
water dispenser. Despite all safety precautions,
there remain residual hazards with every prod-
uct, especially if it is not handled properly.
Every technical device requires regular mainte-
nance and servicing "8. Maintenance and hy. -
giene" on page 33 to work properly. Compli-
ance with all safety and handling instructions
provided is a fundamental requirement for safe
EN
operation. In addition, the local accident pre-
vention regulations and general safety regula-
tions valid at the location of the device apply.
Danger due to electricity! Before
performing maintenance work on
this device, it must be disconnect-
ed from the mains supply.
It must be possible to disconnect the elec-
tric current either by pulling out the power
cable or by means of a biploar mains switch
at the socket.
If the power cable is damaged, it must be
replaced by the manufacturer or a qualified
technician.
Do not use extension cables or multiple
adapters.
Check to ensure that the voltage indicated
on the type plate matches that in the instal-
lation location.
The device must be secured with an earth-
ing switch. Earthing the device is a legal re-
quirement.
The electrical connections must comply
with local standards.
This water dispenser was designed and
constructed in accordance with the Low
Voltage Directive 2014/35/EC and the pro-
tection regulations of the EMV directive
2014/30/EC.
Caution! In the event of any use
other than for the intended purpo-
se, e.g. the use of the water dis-
penser for the treatment of water which is
not of drinking water quality, drinking this
water may constitute a danger to health:
28 BWT AQA drink 1 CAS
• microbiological risk as a result of exposure
to pathogenic germs
• risk due to high concentrations of heavy
metals or organic contaminants
Before maintenance work is carried out on
the drinking water supply, disconnect the
device from the water supply. Rinse the wa-
ter pipe before the device is reconnected.
Comply with all country-specific installation
regulations (e.g. DIN 1988, EN 1717), general
hygiene conditions and technical data rela-
ting to the protection of drinking water.
The materials of the water dispenser which
are in direct contact with the water com-
ply with the regulations and and common
food industry standards. The device was
manufactured according to the provisions
of the Italian Ministerial Decree D.M. 174 of
06/04/2004 and D.M. 25 of 07/02/2012.
Avoid storing the device for unnecessarily
long periods in order to minimise the risk of
microbial contamination.
The lines of the coolant circuit must not be
damaged because they are filled with R134a
gas, which is highly inflammable. Check the
lines on a regular basis.
Set up the unit in a clean, dry and well-ven-
tilated room. The AQA drink 1 CAS water dis-
penser is designed for room temperatures
of between 5 °C and 32 °C – climate class N.
Do not set up the unit near sources of heat
or open flames.
Chemicals, solvents and vapours must not
come into contact with the device. The in-
stallation location must be protected from
frost and direct sunlight.
6.1

WARRANTY AND DISCLAIMER

The specified information and recommenda-
tions, as well as the local drinking water and
waste disposal regulations valid for the appli-
cation in question, must be complied with. All
information and instructions in these installa-
tion and operating instructions take account of
applicable standards and regulations, the state
of the art, as well as our many years of knowl-
edge and experience. Illustrations in this manu-
al are intended to provide a basic understand-
ing and may vary from the actual design of the
device. No claims may be derived from this.
BWT can accept no liability for damage or con-
sequential damage due to: