Seite 1
Einbau- und Bedienungsanleitung Installation and operating instructions Instructions d’installation et d’utilisation Istruzioni di installazione e di utilizzo Apparecchiatura per il trattamento di acque potabili AQA total AQA total Energy 5600, 8400, 11200, 14000 Wichtige Hinweise: Um Fehler zu vermeiden, ist die Einbau- und Bedienungsanleitung stets griffbereit aufzubewahren, vor der Ausführung von Arbeiten am Gerät vollständig durchzulesen und zu beachten.
Vielen Dank für das Vertrauen, das Sie uns durch den Kauf eines BWT Inhaltsverzeichnis Seite 3 Gerätes entgegengebracht haben. Thank you very much for the con- fidence that you have shown in us Table of contents Page 21 by purchasing a BWT appliance.
Inhaltsverzeichnis 1. Allgemeines ................................3 2. Lieferumfang ................................4 2.1. AQA total Energy 5600 ............................. 4 2.2. AQA total Energy 8400 ........................... 4 2.3. AQA total Energy 11200 ............................ 5 2.4. AQA total Energy 14000 ..........................5 3. Einsatzbereich ................................6 3.1.
2. Lieferumfang 2.1. AQA total Energy 5600 2.1.1. Karton mit Zubehör bestehend aus 2 Stück Montagehaken II. 4 Stück Flachdichtungen III. 2 Stück Anschlussverschraubungen (Einlegeteil & Überwurfmutter) IV. 2 Stück Blindverschraubungen (Platte & Überwurfmutter) V. 6 Stück Dübel mit Beilagscheibe und Schraube VI.
2.3. AQA total Energy 11200 2.3.1. Karton mit Zubehör bestehend aus 2 Stück Montagehaken II. 4 Stück Flachdichtungen III. 2 Stück Anschlussverschraubungen (Einlegeteil & Überwurfmutter) IV. 2 Stück Blindverschraubungen (Platte & Überwurfmutter) V. 6 Stück Dübel mit Beilagscheibe und Schraube VI.
Die Wirkeinheit besteht aus einem Grundkörper und – ganz persönlich in Ihr Haus. AQA total Energy von einem Refill mit einer dreidimensionalen Elektro- BWT, mit der neuen 3-Phasen-Technologie: de, welche sich aus elektrisch leitenden und nicht leitenden Partikeln zusammensetzt. Nach Anlegen •...
DIN EN 12502–3: Im Falle einer Ortswasserversorgung empfehlen wir den Rückspülfilter Infinity (Automatik oder Manuell), bei Brunnenwasser einen BWT-Wechselfilter. Bei- Für die Berechnung von S1 werden die einzelnen de können einfach an ein DR-Druckminderer-Modul Werte der Formel in mmol/l angegeben. Für eine angedockt werden.
Für die Berechnung von S sind die in die Formel ein- zusetzenden Werte ebenfalls in mmol/l anzugeben. In Kupferleitungen pH Wert > 7,2 Trinkwasser lt. geltender TVO Nitrat (NO ) < 20 mg/l Sulfat (SO ) < 50 mg/l 5.5. Montage Des Weiteren empfiehlt sich in Zusammenhang mit allen Rohrleitungsmaterialien die Vermeidung von 5.5.1.
5.5.4. AQA total Energy Anschlussverteiler 5.5.5. Die im Lieferumfang enthaltenen anschließen Wirkeinheiten aus der Verpackung nehmen Anschlussmöglichkeiten und Transportverschlusskappe entfernen. Das AQA total Energy Gerät kann von links oder rechts angeströmt werden. Der Wasserausgang Wirkeinheit an AQA total Energy kann ebenfalls auf der linken oder rechten Seite des Anschlussverteiler andocken.
5.5.7. OPTIONAL: Wichtig: Die Reihenfolge der Inbetriebnahme ist Herausführen der ZLT Signale. Die Steuerung unbedingt einzuhalten! des Gerätes ist mit 2 potential freien Relais ausgestattet. Dazu Steuerungskasten 6.1. Absperrventil vor und nach dem AQA total mit dem mitgelieferten Schlüssel öffnen. Die Energy Gerät und Spülventil schließen.
Netzkabel in die dafür vorgesehene Schutzkontakt- 6.10. Spülventil schließen und alle Absperrventile steckdose anstecken. des AQA total Energy Verteilers öffnen. Das AQA total Energy Gerät benötigt ca. 10 6.11. Eventuelle Umgehungsleitung schließen Sekunden um zu Initialisieren. Während dieser Zeit und Absperrventil nach dem AQA total erscheint auf dem LCD im Steuerungskasten: Energy Gerät öffnen.
7. Wartung Wenn die rote CHECK SYSTEM Lampe leuchtet, sollten Sie den Schaltschrank öffnen und den Trinkwasser ist ein Lebensmittel. Regelmäßige Kont- Status auf dem LCD Display ablesen. Dies ist als rolle und hygienische Sorgfalt bei der Durchführung Vorwarnung für einen bevorstehenden Refill- der Arbeiten sollte daher selbstverständlich sein.
Seite 13
Reset Vorgang durchführen: IV.) Menüführung Mit der „–” Taste navigieren Sie im Menü I. Ziehen Sie den Netz-Stecker und nach vorwärts mit der „M” Taste rückwärts. warten Sie 5–10 Sekunden. II. Stecken Sie bei gedrückter (+) Taste beim Display den Netzstecker ein.
7.3. Regelmäßige Wartung/Service Code (-Schlüssel) M ← durch fachkundiges Personal. Um die Funktion des Gerätes zu sichern, muss die Anlage in regelmäßigen ok = (+/c) Abständen (Empfehlung halbjährlich) von fachkundi- gem Personal gewartet werden. Wir empfehlen den Mit der „+” Taste können Sie den Wert der einzelnen Abschluss eines Wartungsvertrages mit unserem Stellen des 3-stelligen Zahlencodes ändern.
III.) Bestätigen Sie Eingabe durch zweimaliges Kontrollieren Sie dann die Drücken der „M” Taste. auf dieser Platine befindli- che Sicherung. IV.) Die Bedienersprache wurde geändert und das AQA total Energy Gerät sollte sich wieder im Kontrollieren Sie danach alle Standbymodus befinden. Steckverbindungen dieser Platine und die Verbindung 8.2.2.
Installationsfirma bzw. unser Werkskundendienst) crt. 1 2 3 durchgeführt werden. Es dürfen ausschließlich Wenden Sie sich bitte an unseren Werkskunden- Original BWT Ersatz- und Verschleißteile verwendet dienst. werden! Wir empfehlen, einen Wartungsvertrag mit Ihrem Installateur oder dem BWT Werkskunden- dienst abzuschließen.
12. Anlagenbuch Zu Ihrer eigenen Information und um Wartungsarbeiten zu erleichtern, bitten wir Sie das Anlagenbuch voll- ständig auszufüllen und immer „griffbereit” aufzubewahren. Gerätetyp: AQA total Energy ________ Händler: __________________________________ Seriennummer: ________________________ __________________________________ Kaufdatum: _____ . _____ . ___________ __________________________________ Errichter der Anlage: _____________________________________________________________________ _____________________________________________________________________...
Allgemeine Daten: Wasserdaten: Leitfähigkeit: ___________ µS/cm Temp. bei der Leitfähigkeitsmessung: ___________ °C pH-Wert: ___________ Temperatur bei der pH-Wertmessung: ___________ °C Calciumkonzentration: ___________ mg/l Gesamthärte: ___________ °dH Carbonathärte: ___________ °dH Entspricht das Wasser der nationalen Trinkwasserverordnung: ❏ ja ❏ nein Das Wasser stammt aus einer ❏...
Table of contents 1. General information ..............................21 2. Scope of delivery ..............................22 2.1. AQA total 5600 ..............................22 2.2. AQA total 8400 ..............................22 2.3. AQA total 11200 ............................... 23 2.4. AQA total Energy 14000 ..........................23 3. Application area ..............................24 3.1.
2.3. AQA total 11200 2.3.1. Box with accessories consisting of 2 mounting hooks II. 4 flat seals III. 2 screw connectors (screws & locking nuts) IV. 2 grub screw connectors (plates & locking nuts) V. 6 dowels with shims and screws VI.
The gentle treatment by AQA total retains all es- ly into your home. sential minerals in the water, above all calcium. AQA total from BWT with the revolutionary 3 phase technology: 4. Installation preconditions • Daily drinking enjoyment full of vital...
5.2. Test section/rinsing valve The installation of a test section is a requirement for AQA total 5600 the warranty – particularly when retrofitting the AQA AQA total 8400 total unit into an existing installation.
Seite 26
• 2 screw connections each consisting of a screw, locking nut and flat seal – AQA total 5600 6/4“ external thread – AQA total 8400 6/4“ external thread To release the rotation safety, press both clips on the – AQA total 11200 2“ external thread retaining ring together and push upwards with both –...
Only plug a plastic plug into the working unit that 3. Replace refill has the same number displayed on the cable chan- nel above the working unit. (Note: Each working unit is assigned a slave circuit board with the corresponding number in the con- 4.
Seite 28
After ca. 10 seconds the display changes to the e.g. a water tap). standby mode: standby AQA total 5600 In addition, the following text must appear on the chan. 1 2 LCD in the control box during water consumption: standby...
6.14. Close control box and lock with supplied Recognising an imminent refill replacement: key. Store key safely away from unauthorized When the red CHECK SYSTEM lamp lights up, open persons. the control box and check the status on the LCD. 6.15.
Implement the reset procedure: I. Disconnect the mains plug and wait approx. 5 – 10 seconds. II. Reconnect the display mains plug while keeping the reset button pressed down (+). III. Only let the (+) button go when standby appears on the display.
8. Operation The 3 digit numerical code is: 369 Code M ← 8.1. Operation hardly required ok = (+/c) During operation, the AQA total unit does not need operating (apart from the refill replacement). The unit adapts itself to the water properties by me- Confirm your entry with the “-”...
IV.) The operating language has been changed Then check all connectors on and the AQA total unit should now be back this board and the connection in Standby mode. of the electrode plug on the corresponding cartridge. 8.2.2. Changing the polarity times If the connections are ok, this Changing the polarity time can affect the working unit must be replaced...
(unit installation company or our works customer ser-vices). Only original BWT spare and wear parts may be used! We recommend that you agree a maintenance contract with your in- staller or with BWT customer services.
12. System logbook For your own information and to facilitate maintenance work, we request that you use the system logbook and always keep it near the unit. Unit type: AQA total _______________ dealer: ________________________________ Serial number: _________________________ ________________________________ Purchase date: _____ .
Seite 37
General data: Water data: Conductivity: ___________ µS/cm Temperature during conductivity measurement: ___________ °C/°F pH value: ___________ Temperature during pH measurement: ___________ °C/°F Calcium concentration: ___________ mg/l Total hardness: ___________ °dH/ppm Carbonate hardness: ___________ °dH/ppm Water complies with national drinking water regulations: ❏...
2. Éléments fournis 2.1. AQA total 5600 2.1.1. Carton avec accessoires, comprenant: 2 crochets de montage 4 joints plats III. 2 raccords vissés (insert et contre-écrou) IV. 2 manchons vissés borgnes (plaque et contre-écrou) 6 chevilles avec rondelle et vis VI.
2.3. AQA total 11200 2.3.1. Carton avec accessoires, comprenant: 2 crochets de montage II. 4 joints plats III. 2 raccords vissés (insert et contre-écrou) IV. 2 manchons vissés borgnes (plaque et contre-écrou) V. 6 chevilles avec rondelle et vis VI. 2 équerres de fixation avec vis de fixation et ressort de compression VII.
De l’eau potable et correctement minéralisée Avec la technologie révolutionnaire AQA total, profitez des bienfaits renouvelés de l’eau potable Une protection efficace contre le tartre. chez vous. AQA total de BWT, avec sanouvelle tech- L’unité active compose d’un...
5. Installation 5.2. Conduite de test / Robinet de rinçage L’installation d’une conduite témoin est une Attention: L’installation doit être effectuée confor- condition indispensable à l’application de la garan- mément aux présentes instructions et aux directives tie, notamment lorsque l’appareil AQA total est ajou- nationales concernant l´eau potable.
• 2 raccords vissés composés d’un insert, d’un contre-écrou et de joints plats – AQA total 5600 filetage extérieur 6/4“ – AQA total 8400 filetage extérieur 6/4“ – AQA total 11200 filetage extérieur 2“...
5.4.5. Déballer l’unité active et enlever 5.4.7. Reports d’alarme (facultatifs) l’obturateur de protection. Sortie des signaux ZLT: La commande de l’appareil est équipée de deux relais sans Monter l’unité active sur le potentiel. Ouvrir le boîtier de commande distributeur AQA total. avec la clé...
Seite 45
Robinet Robinet de rinçage d’arrêt avant l’appareil Après 10 secondes environ, l’afficheur passe en mode d’attente: 6.2. Si l’installation est équipée AQA total 5600 attente d’une conduite de déri- canal 1 2 vation (by-pass), celle-ci attente peut être ouverte AQA total 8400...
Le texte suivant apparaît en outre sur l’afficheur à POWER cristaux liquides dans le boîtier de commande: Couleur: jaune Mode: éclairé fixe AQA total 5600 marche - L’appareil AQA total est raccordé au réseau canal 1 2 électrique AQA total 8400...
7.2. Remplacement des recharges: VIII. Insérez la cartouche neuve L’appareil AQA total indique en temps utile le dans l’unité active. moment de changer les recharges, afin de rester toujours totalement opérationnel. IX. Serrez l’écrou de fermeture jusqu’à la butée. Vous êtes informé de la nécessité de remplacer les cartouches lorsque le voyant rouge CHECK SYSTEM X.
Confirmer la saisie à l’aide de la touche « – ». La saisie V.) Après un court temps d’attente, l’appareil du code vous donne le droit de modifier les paramètres revient en mode de fonctionnement normal. de l’appareil AQA total. N’oubliez pas que les erreurs de paramétrage peuvent entraîner une baisse des perfor- L’indication «...
un code afin d’empêcher les accès non autorisés. Touches de commande Réglages Attention cette manipulation peut engendrer une modification des paramètres de fonctionnement de l’appareil et réduire ainsi son efficacité de traitement. Elle ne peut être effectuée que par des personnes autorisées et sous leur responsabilité.
BWT assure une garantie contractuelle d’1 an à La présence de particules, liée à une mauvaise quali- compter de la date de mise en service.
Seite 51
BWT d’origine. Nous vous conseillons de souscrire un contrat d’entretien auprès de votre installateur ou du ser- vice clientèle de BWT. Correction des erreurs L’appareil signale toutes les erreurs par le clignote- ment du voyant rouge « Entretien » (8 fois/seconde).
12. Journal de l’installation Pour votre information, et pour faciliter les interventions d’entretien, nous vous recommandons de compléter et de garder « sous la main » ce journal de l’installation. Type d’appareil: AQA total ________ Revendeur: _____________________________ Numéro de série: ________________________ _____________________________ Date d’acha:...
Seite 55
Caractéristiques générales: Caractéristiques de l’eau: Conductivité: ___________ µS/cm Température pour la mesure de la conductivité: ___________ °C ___________ Température pour la mesure du pH: ___________ °C Concentration en calcium: ___________ mg/l Dureté totale: ___________ °français Dureté carbonate: ___________ °français Eau conforme à la réglementation nationale sur l’eau potable: ❏...
2. Volume di fornitura 2.1. AQA total 5600 2.1.1. Cartone con accessori composto da 2 ganci di montaggio II. 4 guarnizioni piatte III. 2 raccordi a vite (elemento avvitabile con filettatura esterna & dado a risvolto) IV. 2 raccordi a vite ciechi (piastra &...
2.3. AQA total 11200 2.3.1. Cartone con accessori composto da 2 ganci di montaggio II. 4 guarnizioni piatte III. 2 raccordi a vite (elemento avvitabile con filettatura esterna & dado a risvolto) IV. 2 raccordi a vite ciechi (piastra & dado a risvolto) V.
Questi vengono regolati automaticamente dal contenuti nell’acqua potabile. Il consumo comando elettronico. In conseguenza dello spos- quotidiano consapevole di BWT aqua tamento locale dell’equilibrio tra calcare e anidride rappresenta la vostra fonte di energia sana e carbonica, nell’unità si formano minuscoli cristalli ricca di sostanze vitali ed importanti per il di carbonato di calcio, i cosiddetti nanocristalli.
5. Installazione Attenzione: l’allestimento dell’impianto deve essere Presa di collega- mento alla rete da effettuato conformemente a queste istruzioni di ins- 230V/50 Hz tallazione e di utilizzo, e conformemente all’AVB Was- Contatore ser V (Regolamento sull’approvvigionamento idrico), dell‘acqua art. 12.2, dall’ente erogatore dell’acqua oppure da un’impresa installatrice registrata nell’elenco ufficia- le degli installatori di un ente erogatore dell’acqua 5.2.
• 2 raccordi a vite composti da elemento avvitabile con filettatura esterna, dado a risvolto e guarnizioni piatte – AQA total 5600 filettatura esterna 6/4“ Bordo pavimento finito – AQA total 8400 filettatura esterna 6/4“ 5.4.3. Agganciare il ripartitore di collegamento –...
5.4.5. Togliere dall’imballaggio l’unità attiva 5.4.7. OPTIONAL: compresa nel volume di fornitura e Uscita di segnali ZLT. Il comando rimuovere il tappo di trasporto. dell’apparecchio è dotato di 2 relè a Inserire l’unità attiva sul ripartitore di potenziale zero. Aprire la scatola di collegamento AQA total.
Seite 63
Dopo circa 10 secondi la visualizzazione passa alla la messa in esercizio modalità standby: al fine di garantire standby l’erogazione d’acqua. AQA total 5600 chan. 1 2 Attenzione – con standby la condotta di AQA total 8400 bypass aperta chan.
– controllare le spie sul dispositivo di comando Inoltre durante il prelievo di acqua sull’LCD nella sca- tola di comando deve comparire il testo seguente: Interpretazione delle spie: AQA total 5600 Esercizio POWER Colore: giallo Canale 1 2...
7.2. Sostituzione Refill: dell’unità operativa con la L’apparecchio AQA total visualizza in modo affidabile chiave ottagonale in dotazione quando è necessario sostituire il Refill garantendo e smaltire il refill consumato. così la piena efficienza dell’apparecchio. (rifiuti non riciclabili) Come riconoscere la necessità di sostituzione immi- VIII.
Confermare l’inserimento con il tasto “–” . Inseren- Si spegne la visualizzazione su Standby o Operation. do il codice numerico si ottiene l’autorizzazione a Se dopo la messa in funzione la spia rossa “Check modificare le impostazioni dell’apparecchio AQA System“ non si spegnesse oppure in fase di prelievo total.
8.2.1. Modifica della lingua dell’utente Sono disponibili le seguenti lingue: Inglese, francese, spagnolo, italiano, tedesco Tasti di comando I.) Navigare come descritto precedentemente finché appare la seguente visualizzazione sul III.) Inserimento del codice display LCD: Premendo il tasto “M” passare alla modalità per language: eseguire impostazioni sul comando elettronico.
Accertarsi che sia stato installato un filtro per acqua potabile a monte dell’impianto e che l’acqua corris- ponda alla legislazione nazionale in materia di acqua potabile. Sensore Hall 9.1. Segnalazioni di guasto/Eliminazione guasti Corrente insufficiente crt. 1 2 3 Sensore Hall 9.1.1.
Seite 69
Possono essere utilizzati es-clusivamente parti di ricambio e soggette ad usura originali della BWT! Si consiglia di stipulare un contratto di manu- tenzione con il proprio instal-latore o con il servizio clienti di fabbrica BWT.
12. Registro dell’impianto Per vostra informazione e per facilitare i lavori di manutenzione, siete pregati di compilare in ogni parte il registro dell’impianto e di conservarlo sempre a portata di mano. Modello apparecchio: AQA total ________ Rivenditore: _____________________________ Numero di serie: ________________________ _______________________________________ Data di acquisto: _____ .
Seite 72
Manutenzione: Data: _____ . _____ . ___________ eseguita da: ________________________________ difetti rilevati: ___________________________________________________ ___________________________________________________ ___________________________________________________ lavori eseguiti: ___________________________________________________ ___________________________________________________ ___________________________________________________ prossima manutenzione consigliata: ___________________________________________________ Manutenzione: Data: _____ . _____ . ___________ eseguita da: ________________________________ difetti rilevati: ___________________________________________________ ___________________________________________________ ___________________________________________________ lavori eseguiti: ___________________________________________________ ___________________________________________________ ___________________________________________________...
Seite 73
Dati generali: Dati sulla qualità dell’acqua: Dati sulla qualità dell’acqua: ___________ µS/cm Temp. alla misurazione della conduttività: ___________ °C Valore di pH: ___________ Temp. alla misurazione del valore di pH: ___________ °C Concentrazione di calcio: ___________ mg/l Durezza totale: ___________ °dH Durezza totale: ___________ °dH L’acqua soddisfa il regolamento nazionale sull’acqua potabile:...