Maintenance And Cleaning; Electrical Connection - Scheppach ASP50-ES Originalbetriebsanleitung

Check that the connection is secure and airtight.
• Set the switch on the vacuum system to position "I"
= Automatic mode.
Dry vacuuming (fig. 3+12+13)
Use the folded filter (24) for dry vacuuming. The pa-
per filter bag (23) can be used in addition. This en-
sures that the folded filter (24) remains free of dust for
longer and maintains the vacuum power for longer.
In addition, the disposal of the dust is also easier.
Always ensure that the filters are correctly fitted.
Wet vacuuming (fig. 3+11)
Use the foam filter (22) for wet vacuuming. Ensure
that the foam filter (22) is correctly fitted.
If the stainless steel container (15) is full, the safety
float valve (20) closes the suction port and suction
operation is interrupted.
m IMPORTANT!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam filter
(22) provided.
Drain hose (11) (fig. 20)
The stainless steel container (15) is equipped with
a water drain hose (11) in order to make it easier to
drain. To do so, pull the stopper (7) out of the drain
hose (11) and drain off the liquid. Then insert the stop-
per (7) again.

9. Maintenance and cleaning

m WARNING!
Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
Cleaning
It is recommended to clean the device after each use.
Do not spray the device with water or clean it under
running water. This can result in electric shocks and
can damage the device.
Empty the stainless steel container (15) after each
use: After opening the stopper in the drain hose (7),
the liquid collected can be drained out. Residual li-
quid remains in the stainless steel container (15). To
remove residual liquid, take off the machine head (2)
by releasing the locking hooks (5) from the stainless
steel container (15). Pour out the liquid residue. Clean
the container with a damp cloth.
• Replace paper filter bag when full
• Always keep the device clean. Do not use cleaning
agents or solvents.
• Keep the ventilation slots clean and free of dirt and dust.
• Clean the device only with a soft brush or a damp cloth.
• Clean the foam filter (22) with a little soap and run-
ning water and then leave it to air dry.
Maintenance
The device is maintenance-free.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables. Wear parts*:
* Not necessarily included in the scope of delivery!
• Foam filter
• Paper filter bag
• Folded filter for dry vacuuming
10. Storage
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
• There are recesses in the wheel mounting base (10)
at the rear of the machine and on the machine head
(2) for storing the floor nozzle (25), the joint nozzle
(26) and the metal extension tube (27).
• The mains cable (3) can be wound around the push
grip (4). (Fig. 21)

11. Electrical connection

The electrical motor installed is connected and ready for
operation. The connection complies with the applicable
VDE and DIN provisions.
The customer's mains connection as well as the exten-
sion cable used must also comply with these regulations.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F".
17 І 64 17 І 64