Operation; Maintenance And Cleaning; Storage - Scheppach ASP30-ES Original Bedienungsanleitung

8. Operation

m WARNING!
Switch the device off if liquid or foam emerges with
the exhaust air during wet vacuuming.
Switch on / switch off / automatic (Fig. 16, 17)
The ON/OFF switch (12) has three settings:
1 switch setting 0: Off
2 switch setting II: On
• Press the on/off switch (12) to switch on.
• Press the on/off switch (12) again to switch the de-
vice off.
3 switch setting I: Automatic mode (the vacuum
cleaner will be switched on by an electric tool).
• Plug your electrical tool's cable into the automatic
socket (fig. 17).
• Connect the suction hose to the suction connection
on your electrical tool. Check that the connection is
secure and airtight.
• Set the switch on the vacuum system to position "I"
= Automatic mode.
Dry vacuuming (Fig. 3, 9, 10)
Use the folded filter (19) for dry vacuuming. The pa-
per filter bag (18) can be used in addition. This en-
sures that the folded filter (19) remains free of dust for
longer and maintains the vacuum power for longer.
In addition, the disposal of the dust is also easier.
Always ensure that the filters are correctly fitted.
Wet vacuuming (Fig. 3, 8)
Use the foam filter (17) for wet vacuuming. Ensure
that the foam filter (17) is correctly fitted.
If the stainless steel container (9) is full, the safety
float valve (15) closes the suction port and suction
operation is interrupted.
m IMPORTANT!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam fil-
ter (17) provided.
Water drain plug (8) (Fig. 18)
The stainless steel container (9) is equipped with a
water drain plug (8) in order to make it easier to drain.
Open the water drain plug (8) by turning it counter-
clockwise and drain out the liquid.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

9. Maintenance and cleaning

m WARNING!
Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
Cleaning
It is recommended to clean the device after each use.
Do not spray the device with water or clean it under
running water. This can result in electric shocks and
can damage the device.
Empty the stainless steel container (9) after each use:
After opening the screw cap to drain out the liquids
(8), the liquid collected can be drained out. Residual
liquid remains in the stainless steel container (9).
To remove residual liquid, take off the machine head
(2) by releasing the locking hooks (4) from the stain-
less steel container (9). Pour out the liquid residue.
Clean the container with a damp cloth.
• Replace paper filter bag when full
• Always keep the device clean. Do not use cleaning
agents or solvents.
• Keep the ventilation slots clean and free of dirt and
dust.
• Clean the device only with a soft brush or a damp
cloth.
• Clean the foam filter (17) with a little soap and run-
ning water and then leave it to air dry.
Maintenance
The device is maintenance-free.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables. Wear parts*: Foam filter, Paper filter
bag, Folded filter for dry vacuuming
* Not necessarily included in the scope of delivery!

10. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.
• Wind the mains cable (3) around the top cable
holder (13) at the connection port for the blow-
er function (14) and the bottom cable holder (24).
(Fig. 19)
GB | 19