Installation; Operation; Maintenance And Cleaning - Scheppach NTS20 Original Bedienungsanleitung

7. Installation

m IMPORTANT!
Prior to use, ensure that the device has been cor-
rectly and fully assembled.
Unpacking (fig. 1, 2, 3)
1 Release the locking hooks (4) and remove the ma-
chine head (2). The accessories are located inside
the stainless steel container (7). Only the plastic
extension tubes (3x) (7) are located outside the
stainless steel container, in the packaging. Remove
all of the accessories from the stainless steel con-
tainer (7).
Installing the castors (fig. 4)
1. Press the four castors (5) into the holes in the cas-
tor mounts.
Installing the machine head (2) (fig. 5)
1 Place the machine head (2) on the stainless steel
container (7). Secure the machine head (2) with
the locking hooks (4). When installing the machine
head (2), ensure that the locking hooks (4) latch into
place correctly.
Installing the foam filter (14) (fig. 6)
Never use the device without filter! Always ensure
that the filters are correctly fitted!
Installing the foam filter (14): For wet vacuuming, slide
the foam filter (14) provided over the filter basket with
safety float valve (12).
Installing the paper filter bag (15) (fig. 7)
It is recommended to use an additional paper filter
bag (15) when vacuuming fine, dry dirt. Slide the
paper filter bag (15) over the suction opening in the
stainless steel container (7). The paper filter bag (15)
is only suitable for dry vacuuming. The paper filter
bag (15) makes it easier to dispose of the dust col-
lected.
Installing the suction hose (fig. 8, 9)
Connect the suction hose (13) to the corresponding
port, depending on the desired use, on the wet and
dry vacuum.
Vacuuming:
Connect the suction hose (13) to the suction hose port
(8). To do so, slide the end of the suction hose (13)
into the suction hose port (8). Make sure the plug-in
fitting on the end of the suction hose (13) latches into
the recess on the suction hose connection (8). In the
end position, turn the suction hose (13) in a clockwise
direction.
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Blowing:
Connect the suction hose (13) to the suction hose
port (11). Make sure the plug-in fitting on the end of
the suction hose (13) latches into the recess on the
connection with blast function (11). In the end posi-
tion, turn the suction hose (13) in a clockwise direc-
tion.
Installing the plastic extension tubes, suction
hose and floor nozzle (fig. 10)
Assemble the plastic extension tubes (18) by pushing
them together. Connect the assembled plastic exten-
sion tubes with the bent end of the suction hose (13).
Fit the floor nozzle (16) or joint nozzle (17) to the other
end of the assembled plastic extension tubes.

8. Operation

m WARNING!
Switch the device off if liquid or foam emerges with
the exhaust air during wet vacuuming.
Switching on/off (fig. 1)
Press the on/off switch (9):
• Switch setting 0: Off
• Switch setting I: On
Dry vacuuming
Use the paper filter bag (15) for dry vacuuming.
Wet vacuuming
Use the foam filter (14) for wet vacuuming. Ensure
that the foam filter (14) is correctly fitted.
If the stainless steel container (7) is full, the safety
float valve (12) closes the suction port and suction
operation is interrupted.
m IMPORTANT!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam fil-
ter (14) provided. To remove the liquid vacuumed up
from the stainless steel container, take off the ma-
chine head (2) by releasing the locking hooks (4) from
the stainless steel container (7). Pour out the liquid
residue.

9. Maintenance and cleaning

m WARNING!
Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
Cleaning
It is recommended to clean the device after each use.
Do not spray the device with water or clean it under
running water. This can result in electric shocks and
can damage the device.