Installing And Adjusting Bowden Ca- Bles For Travel And Worm Drives (06 - 11); Adjusting The Bowden Cable (12); Checking The Bowden Cable Setting (13); Mounting The Rod For The Gear Selec- Tor Lever (14, 15) - AL-KO SnowLine 620 E III Betriebsanleitung

GB
4. Left upper brace: Insert 2 bolts (05/1) through
upper brace, lower brace and mounting
bracket and tighten slightly with washers and
nuts.
5.3 Installing and adjusting Bowden cables
for travel and worm drives (06 - 11)
1. Attach the Bowden cable (06/1) for the travel
drive (06/2) into the lower hole (06/3) of the
right-hand lever.
2. Attach the Bowden cable (07/1) for the worm
drive (07/2) into the upper hole (07/3) of the
left-hand lever.
3. Adjust the Bowden cables as follows:
■
Turn the adjuster on the Bowden cable
(08/1) in the direction of the arrow (08/a)
until the Bowden cable no longer sags (is
slightly tensioned). While turning the ad-
juster, hold the cable so that it does not
become twisted.
■
Tighten lock nut (08/2) (08/b).
4. Fix the Bowden cables (09/1) with the clamps
(09/2) on the left and right of the handlebar.
5. Tension the Bowden cable:
■
Loosely tighten the lock nuts (10/1, 11/1).
■
Turn the threaded end piece (10/2, 11/2)
upwards until the Bowden cable is ten-
sioned.
■
Turn the lock nuts against the guide
(10/3, 11/3) to fix the Bowden cable.
6. Pull down the rubber sheath (10/4, 11/4) to
the lock nut (10/a, 11/a) to protect the
Bowden cable against corrosion.
5.4

Adjusting the Bowden cable (12)

The fine adjustment is carried out via the adjust-
ing screw.
1. Loosen the lock nut (12/2) on the adjusting
screw (12/a).
2. Turn the adjusting screw (12/3) (12/b) to
lengthen or shorten the path of the Bowden
cable. Ensure that the Bowden cable is
slightly taut and is not sagging.
3. Re-tighten the lock nut (12/2) (12/a).
5.5

Checking the Bowden cable setting (13)

The Bowden cable of the travel drive lengthens
over time. If the travel drive can no longer be
switched on while the engine is running, the
Bowden cable has become too long and must be
tightened.
36
1. Switch off the appliance (see chapter 6.8
"Stopping the engine (37, 38)", page 39).
2. Re-adjusting the Bowden cable (see chapter
5.3 "Installing and adjusting Bowden cables
for travel and worm drives (06 - 11)",
page 36).
To check the Bowden cable setting:
1. Start the engine (see chapter 6.7 "Starting
the engine (31 – 36)", page 38).
2. Put into gear (see chapter 7.1 "Starting clear-
ing (39 - 41)", page 39).
3. Slowly push the right handle (13/1) down-
wards (13/a) until a slight resistance is felt.
The pressure point of the clutch has been de-
termined.
4. If the travel drive is not switched on: Repeat
the previous steps.
5. If adjusting the Bowden cable is not success-
ful: Contact one of the manufacturer's service
centres.
5.6 Mounting the rod for the gear selector
lever (14, 15)
1. Attach the rod (14/1) at the bottom into the
gear shift mount (15/2).
2. Attach the rod on the top of the gear selector
lever (15/3) in the mount.
3. Secure the rod at the top and bottom with
washers and cotter pins.
5.7 Fitting the levers for gear selection and
discharge height (16)
1. Fit spring washers (16/1) onto the thread.
2. Screw on and tighten the discharge height le-
ver (16/2).
3. Screw on and tighten the gear selection lever
(16/3).
5.8 Plugging in the heater and lighting plug
(17)
1. Connect the plug parts (17/1) for the heater
and lighting.
2. Secure the plug connection.
5.9 Fitting the snow discharge spout (18-
21)
1. Apply spray oil (or grease) to the sliding sur-
face (18/1) of the snow discharge spout on
the snow blower.
2. Fit the snow discharge spout (19/1) (19/a, 20/a).
Assembly