Mounting The Intermediate Brace (03); Mounting The Upper Brace (04); Fixing The Cables To The Bar (05); Installing The Adjustment Crank (06, 07) - AL-KO ST 4048 Betriebsanleitung

Commissioning/Decommissioning

4.3

Mounting the intermediate brace (03)

1. Push both ends of the intermediate brace
(03/1) onto the lower brace (03/2) (03/a) in
such a way that the insertion holes of the in-
termediate brace and lower brace line up.
The guide (03/3) for the adjusting crank must
point upwards.
2. Insert two long locking screws (03/4) from the
inside.
3. Place a washer (03/5) on each of the locking
screws.
4. Screw star handles (03/6) onto the locking
screws and firmly tighten.
4.4

Mounting the upper brace (04)

1. Push both ends of the upper brace (04/1)
onto the intermediate brace (04/2) (04/a) in
such a way that the insertion holes of the up-
per brace and intermediate brace line up.
The motor switch, motor switch bracket,
handle and LED light must point upwards.
2. Insert two long locking screws (04/3) from the
inside.
3. Place a washer (04/4) on each of the locking
screws.
4. Screw star handles (04/5) onto the locking
screws and firmly tighten.
4.5

Fixing the cables to the bar (05)

1. Fix the cable (05/1) of the motor switch with a
cable holder (05/2) to the intermediate brace
and to the lower brace.
2. Fix the cable (05/3) of the LED light with a
cable holder (05/2) to the intermediate brace
and to the lower brace.
4.6

Installing the adjustment crank (06, 07)

Connecting the adjustment crank to the
extension shaft (06)
1. Insert the adjusting crank (06/1) through the
guide (06/2) onto the intermediate brace (06/
a) from above.
2. Insert the adjustment crank into the support
(06/3) of the extension shaft up to the end
stop (06/b).
3. Align the adjusting crank and the extension
shaft so that their holes line up.
4. Push a cotter pin (06/4) through both bores
(06/c) until it clicks into place.
469905_a
Installing and fixing the adjustment crank
onto the appliance (07)
1. Insert the extension shaft (07/1) into the
mounting (07/2) on the appliance (07/a).
2. Rotate the extension shaft so that its hole
and the hole of the mounting line up.
3. Push a cotter pin (07/3) through both bores
(07/b) until it clicks into place.
4. Turn the star handle (07/4) onto the guide
(07/5) and slightly tighten it to fix the adjust-
ment crank (07/c) in place.
4.7

Installing the snow deflector (08)

1. Place the snow deflector (08/1) on the dis-
charge channel (08/2) so that the lugs (08/3)
engage in the recesses of the snow deflector
on the left and right.
2. Insert two short locking screws (08/4) through
the holes of the discharge channel from the
inside.
3. Place a washer (08/5) on each of the locking
screws.
4. Screw star handles (08/6) onto the locking
screws and firmly tighten.
5 COMMISSIONING/
DECOMMISSIONING
5.1 Charging the rechargeable battery (09,
10)
The rechargeable battery and the charging unit
are not included. The following li-ion re-
chargeable batteries and charging units from AL-
KO can be used:
Product Designation
Li-ion re- B150 Li (B05-3640)
chargeable
battery
Li-ion re- B200 Li (B05-3650)
chargeable
battery
Charging C05-4230
unit
The rechargeable battery is partially charged.
Fully charge the rechargeable battery before us-
ing it for the first time. The rechargeable battery
can be charged in any charge status. Interrupting
charging does not damage the rechargeable bat-
tery.
Art. no.
113280
113524
113281
37