Fitting The Lower Brace (04, 05); Hooking In And Adjusting The Bowden Cables (06 - 11); Fitting The Gear Selector Lever (12 - 14); Fitting The Snow Discharge Spout (15- ■ 18) - AL-KO SnowLine 560 II Betriebsanleitung

GB
No. Tool
3 5 mm Allen key
4 Combination or long-nose pliers
5 Screwdriver
6 Spray oil
7 Tyre pump with pressure gauge (car tyre
valve)
5.1

Fitting the lower brace (04, 05)

Mount the lower brace on the left and right at the
bottom of the snow blower.
1. Undo the screws (04/1).
2. Attach the lower brace (05/1).
3. Insert the bolts (05/2) through the lower
brace and tighten.
5.2 Hooking in and adjusting the Bowden
cables (06 - 11)
1. Lay Bowden cables upwards:
■
Guide the Bowden cable (06/1) for the
auger drive through the opening in the
gear selector plate (06/2) (06/a).
■
Lay the Bowden cable (07/1) for the trav-
el drive upwards through the recess in
the gear selector plate (07/a).
2. Unscrew the Z-end pieces (08/1) from the ad-
justers (08/2) of the two Bowden cables. The
lock nuts (08/3) remain on the Z-end piece.
3. Flip both clutch levers (09/1) upwards (09/a).
4. On both clutch levers: Hook in the Z-end
piece (10/1) from the inside of the guide rail
into the bore (10/2) on the clutch lever (10/3).
5. On both clutch levers: Turn the adjuster
(11/1) onto the suspended Z-end piece (11/2)
(11/a) until the Bowden cable no longer sags,
i.e. is slightly taut.
Note: Hold the cable firming while turning, so
that it does not become twisted.
6. Tighten lock nut (11/3) (11/b).
5.3 Fitting the gear selector lever (12 – 14)
1. Unscrew the nut (12/1) from the horizontal
fastening screw (12/2) (12/a) and pull the
mounting bolt out of the connecting bolt
(12/3) (12/b).
2. Insert the gear selector lever (13/1) through
the gear selector plate (13/2) (13/a).
3. Place the gear selector lever (14/1) on the
connecting bolt (14/2) (14/a).
34
4. Insert the horizontal mounting bolt and un-
screw the self-locking nut (14/3), but do not
tighten it yet.
5. Use the adjusting screw (14/4) to adjust the
inclination of the gear selector lever in such a
way that it engages in the recess for first gear
(13/3).
6. Move the gear selector lever through all
gears and check that the process is smooth.
If not, adjust the adjustment screw.
7. Tighten the lock nut (14/5) of the adjustment
screw.
8. Tighten the self-locking nut on the horizontal
mounting bolt.
5.4 Fitting the snow discharge spout (15-
18)
1. Apply spray oil (or grease) to the sliding sur-
face (15/1) of the snow discharge spout on
the snow blower.
2. Fit the snow discharge spout (16/1) (16/a, 17/
a).
3. Insert the mounting bolts (17/2) through the
brackets and snow discharge spout from the
inside.
4. Secure the snow discharge spout with the
self-locking nuts (17/3).
5. Insert mounting bolts (18/1) through the large
guide plate (18/2)
6. Fit the small guide plate (18/3).
Note: The small guide plate must lie on top
of the large guide plate.
7. Insert the guide plates with the mounting
bolts from below into the snow discharge
spout (18/a).
8. Fit washers (18/4) onto the bolts.
9. Securely tighten the self-locking nuts (18/5).
5.5 Mount the hand crank for the snow
discharge spout (19 – 25)
1. Remove the handle (19/1) from the connect-
ing rod:
■
Unscrew the mounting bolt (19/2) (19/a).
■
Remove the washer (19/3).
2. Insert the connecting rod (20/1) with the han-
dle side from below into the upper guide
(20/2) on the guide bar (20/3) (20/a).
Note: The guide is already fitted.
3. Remove the safety pin (21/1) and washer
(21/2) at the bottom of the connecting rod
(21/a).
Assembly