Technical Data; Before Starting The Equipment - Scheppach MGT410 Originalbetriebsanleitung

and arms if the device is used for a long time or if
the device is not guided and evaluated properly.
Despite the observance of the operating instructions
there still may be some hidden residual risks.

Technical data

Pole Saw
Cutter bar length
Max. Cutting length
Chain pitch
Chain thickness
Sprocket wheel
Cutting speed at rated
rpm:
Oil tank capacity
Net weight without acces-
sories:
Saw chain
Cutter bar
Lithium-ion battery
Voltage
Capacity
Charging time
Charging unit
D E / A T / C H M F M F D E / A T / C H Input voltage
Power rating
Output voltage
Output current
Protection Class
Sound and vibration
Sound and vibration values were measured in ac-
cordance with ISO 22868.
L sound pressure level
pA
K uncertainty
WA
L sound power level
WA
measured
K uncertainty
WA
L sound power level gu-
WA
aranteed
Wear ear-muff s.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with ISO 22867.
Vibration emission value a
Unsicherheit K uncertainty
The specifi ed vibration value was established in ac-
240 mm
200 mm
3/8"
1.3 mm
6 Teeth, 3/8"
4 m/s
0.08 l
3,2 kg
Oregon 91PX033X
Oregon 080NDEA318
18 V DC
1500 mAh
75 min
100-240 V AC / 50-60 Hz
40 W
21 V DC
1.5 A (h)
II
Pole Saw
68.9 dB(A)
3 dB(A)
88.9 dB(A)
3 dB(A)
93 dB(A)
Pole Saw
1.635 m/s
2
h
1.5 m/s
2
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specifi ed value in exceptio-
nal circumstances.
The specifi ed vibration value can be used to compare
the equipment with other electric power tools.
The specifi ed vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a mi-
nimum.
• Only use appliances which are in perfect working or-
der.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Before starting the equipment

Caution! Do not fi t the battery until the equipment has
been fully assembled and all the settings have been ac-
tuated. Always wear protective gloves when working on
the equipment to protect yourself against injury. Careful-
ly unpack all parts and check that they are complete.
Assembly
Fitting the chain saw mounting kit (for use as a pole-
operated pruner)
Assembly of the cutter rail and the saw chain
• Undo the fi xing screw (17) of the chain wheel
• cover (Fig. 2).
• Take off the chain wheel cover (18). (Fig.3)
• Lay the chain as shown in the groove which runs
around the cutter rail (Fig. 4/Item 19).
• Insert the cutter rail and chain as shown in the moun-
ting in the chainsaw (Fig. 5).
• At the same time guide the chain around the chain
wheel (Fig. 5/Item 20).
• Attach the chain wheel cover (Fig. 6/Item 18) and
fasten it hand-tight with the fastening screw.
Important! Do not fully tighten the fastening screw until
after you have adjusted the chain tension.
Tensioning the saw chain
Caution! Always remove the battery from the device be-
fore inspection and adjustment. Always wear protective
gloves when working on the chainsaw to protect yourself
against injury.
• Undo the fi xing screw (18) of the chain wheel cover a
few turns (Fig. 6).
• Adjust the chain tension with the chain tensioning
screw (Fig. 7/Item 21). Turning the screw clockwise
increases the chain tension, turning it counter-clock-
wise decreases the chain tension. The saw chain is
correctly tensioned if it can be lifted approx. 2 mm in
the middle of the cutter rail (Fig. 8).
• Secure the fi xing screw (18) of the chain wheel cover
(Fig. 6).
Notice! All the chain links must lie properly in the guide
groove of the cutter bar.
Notes on tensioning the chain:
The saw chain must be properly tensioned to ensure
23 І 44