Electrical Connection - Elica NIKOLATESLA FIT Montage- Und Gebrauchsanweisungen

cooked flambè. Using a naked flame may damage the filters
and cause a fire hazard; it must, therefore, be avoided under
all circumstances. Extra care must be taken when frying to
prevent the oil from overheating and catching fire. ● Please
note! The accessible parts of the device may become hot
when the hob is switched on. ● Please note! Do not connect
the device to the electric power supply until installation has
been fully completed. The regulations laid down by local
authorities must be strictly followed with regard to the
technical and safety measures to adopt for fume extraction. ●
The extracted air must not be conveyed through the same
ducts used to extract the fumes generated by gas combustion
or other types of combustion devices. Never use the device
without the grille properly installed! Only use the fastening
screws supplied with the device for installation, or if not
supplied, purchase the correct type of screws. Use screws of
the right length, as indicated in the installation guide. ● When
the device is used together with other devices powered with
non-electrical energy, the negative pressure of the room must
not exceed 4 Pa (4 x 10●5 bar). This manual must be stored
for future consultation at any time. If sold, transferred or
moved, it must remain with the device.● Range hoods and
other cooking fume extractors may adversely affect the safe
operation of appliances burning gas or other fuels (including
those in other rooms) due to back flow of combustion gases.
These gases can potentially result in carbon monoxide
poisoning. After installation of a range hood or other cooking
fume extractor, the operation of flued gas appliances should
be tested by a competent person to ensure that back flow of
combustion gases does not occurs. ● Range hoods and other
cooking fume extractors may adversely affect the safe
operation of appliances burning gas or other fuels (including
those in other rooms) due to back flow of combustion gases.
These gases can potentially result in carbon monoxide
poisoning. After installation of a range hood or other cooking
fume extractor, the operation of flued gas appliances should
be tested by a competent person to ensure that back flow of
combustion gases does not occur.

Electrical connection

Fig. 7 - 7.1 - 7.2 - 7.3
● Disconnect the device from the electric power supply. ●
Installation must be carried out by professionally qualified
personnel with knowledge of the regulations in force for
installation and safety. ● The manufacturer denies all liability
to persons, animals or property if the guidelines provided in
this chapter are not followed. ● The power cable must be long
enough to allow the hob to be removed from the worktop. ●
Make sure that the voltage on the serial number data plate on
the bottom of the device corresponds to that of the domestic
environment where it will be installed. ● Do not use extension
leads. ● The earth power cable must be 2cm longer than the
other cables. ● If the electrical appliance is not supplied with a
power cable, use one with a minimum conductor diameter of
2.5 mm2 for power up to 7200 Watt; for higher power levels,
the diameter must be 4 mm2. ● The temperature must not
reach 50°C above room temperature anywhere along the
cable. ● The appliance is intended for permanent connection
to the power supply.
● Please note! Before reconnecting the circuit to the mains
power supply, make sure that it is working correctly, always
check that the power cable is correctly installed. ● Please
note! The interconnection cable must be replaced by the
authorised technical support service or by a person with
similar qualifications.
Note : the product is equipped with a Power Limitator
function, which allows a maximum power limit to be set
The limit must be set at the time of the product's connection to
the electrical network or when the electrical network itself is
reconnected (within the following 2 minutes). Size the
electrical system protection according to the selected Power
Limitation level. For the Power Limitation setting sequence,
see the Operation section of this manual.
Installation
● Both electric and mechanical installation must be carried out
by specialised personnel.
The electrical appliance is designed to be built into a work top
with a thickness of 2-6 cm in the case of TOP installation; 2.5-
6 cm in the case of FLUSH installation.
The minimum distance between the hob and the wall must be
at least 5 cm in front, at least 4 cm on the sides and at least
50 cm from overhead wall units.
NB = The recommended distances are given as examples:
when planning the spaces, the indications of the kitchen
manufacturer must be observed.
Mounting
Before starting the installation:
• After unpacking the product, check that it has not
been damaged during transport and in the event of
problem, please contact the reseller or the Customer
support service before installing it.
• Check that the product is the right size for the installation
area.
• Check for accessories (e.g. bags containing screws,
warranty certificates, etc.) inside the packaging (placed
there for transport reasons). Remove and keep them
safe, if present.
• Also check that there is a power socket near the
installation area.
Preparing the cabinet for installation:
- The product cannot be installed above cooling appliances,
dishwashers, heaters, ovens, washing machines and
dryers.
- Create the cut-outs in the cabinet before inserting the hob
and carefully remove any shavings or sawdust.
- to optimise the filter installation, it is advisable to cut a
slot in the plinth to insert a grille (available on the market)
IMPORTANT: use a single-component adhesive sealant (S),
which withstands temperatures up to 250°; before
installation, thoroughly clean the surfaces to stick and
eliminate any substance that may compromise adhesion,
(e.g. release agents, preservatives, fats, oil, dust, traces
17