Cooking Containers - Elica NIKOLATESLA FIT Montage- Und Gebrauchsanweisungen

of old adhesives, etc.); the adhesive should be uniformly
spread all around the outside of the frame; after sticking,
leave the adhesive to dry for about 24 hours.
Caution! Failure to install screws and fasteners in accordance
with these instructions may result in electrical hazards.
Note: to ensure the correct installation of the product, it is
recommended to tape the pipes using an adhesive with the
following characteristics:
- soft elastic PVC film, with an acrylic-based adhesive
- compliant with DIN EN 60454 regulations
- flame retardant
- excellent resistance to wear
- resistant to temperature fluctuations
- can be used at low temperatures
The device can also be used in combination with a
Window sensor KIT (not supplied by the manufacturer).
If the Window sensor KIT is installed (only in the case of use
in EXTRACTOR mode), air extraction will halt every time the
window in the room, on which the KIT is applied, is closed.
• The KIT must be electrically connected to the device by
qualified and specialised technical personnel.
• The KIT must be certified separately in accordance with
the safety standards for the component and its use with
the device. Installation must be carried out in accordance
with current regulations for domestic systems.
PLEASE NOTE:
• the wiring of the KIT to be connected to the device must
be part of a certified safety extra-low voltage (SELV)
circuit.
• the manufacturer of this device declines all liability for
any inconvenience, damage or fires caused by defects
and/or problems associated with the malfunction and/or
incorrect installation of the KIT.
This device is marked in compliance with the European
Directive 2012/19/EC - UK SI 2013 No3113, Waste Electrical
and Electronic Equipment (WEEE). By ensuring that this
device is disposed of correctly, the user will help prevent
potential negative impacts on the environment and human
health.
The symbol on the device or documentation provided
indicates that this device must not be treated as domestic
waste, but must be taken to a suitable waste collection site for
the recycling of electrical and electronic appliances. Dispose
of it in accordance with local regulations for waste disposal.
For further information about the treatment, recovery and
recycling of this device, please contact your local authority,
the collection service for household waste or the shop from
where the device was purchased.
Device designed, tested and developed in compliance with
regulations on:
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-6, EN/IEC 60335-
2-31, EN/IEC 62233.
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO
5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3;
ISO 3741; EN 50564; IEC 62301.EN 60350-2;
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2;
EN/IEC 61000-3-3; EN/IEC 61000-3-12.
Recommendations for correct use in order to reduce the
impact on the environment: When you start cooking, turn the
device on at minimum speed, leaving it on for a few minutes
when you have finished cooking. Increase the speed only if
there is a large quantity of fumes and steam, using the
Booster function only in extreme cases. To keep the odour
reduction system running efficiently, replace the carbon filter/s
when necessary. To ensure the high performance of the
grease filter, clean it when necessary. To improve efficiency
and minimise noise, use the maximum duct diameter indicated
in this manual.
2. Use

Cooking containers

Only use pans that carry the
Important:
to avoid permanent damage to the hob surface, do not use:
• containers with a base that is not perfectly flat;
• metal containers with an enamelled base;
• containers with a rough base, to avoid scratching the hob
surface;
• never place hot pots and pans on the surface of the hob's
control panel.
Not all pans suitable for induction work in an efficient
manner due to the base only partially consisting of
ferromagnetic material! When purchasing pots or pans
ensure that:
• that the base is made entirely from ferromagnetic material.
If this is not the case, the efficacy of the transmission of
heat is lessened and the uniformity of heat and the
temperature of the pot/pan may not be suitable for cooking.
• The base does not contain aluminium: the crockery does
not heat and may not be recognised by the inductors.
• Bases that are not flat or that have rough surfaces.
These lower the contact surface area between the
inductor and the pan, lowering efficiency and harming the
cooking experience.
18
symbol.
NO!
NO!