Scheppach MFH380-20Li Dual Original Anleitungen Seite 32

Do not overload the engine, and do not use it for work
–
the tool is not designed for.
Always make sure the ventilation openings are free
–
of dirt.
Store the tool out of the reach of children.
–
Store the tool at a safe and dry location.
–
Check the engine for damages after impact, or other dam-
–
ages.
Keep body parts and pieces of clothing away from the
–
trimmer head when you start the engine, or keep it
running.
Always keep in mind that especially during trim-
–
ming of lawn edges, gravel enclosures, and similar
locations stone and dirt can be hurled away from
the cutting line.
Never cross roads or paths when the tool is switched
–
on.
Never cut against hard objects such as stone, etc.
–
This way you avoid injuries, and damages to the
tool.
When using metal cutting tools, there is a basic
–
risk of kickback if the tool meets a fixed obstruction
(stones, trees, branches etc.). In this event, the tool
is whipped back in the opposite direction of rotation.
Never use the tool without the guards attached.
–
Never use your hands to stop the cutting device.
–
Always wait until it stops on its own.
–
Hold and guide the trimmer head as close to the
–
ground as possible.
Only cut grass growing on the ground. Do not cut
–
grass in cracks in walls, growing or on rocks, etc.
Always make sure no objects, or other debris is col-
–
lecting in the trimmer head, in the protective hood,
or in the engine.
Only use the tool, when the guard is attached.
–
Always switch off the tool, before you put it down.
–
Keep in mind that there is risk of injuries in the area
–
of the cutting device intended to cut off the line.
CAUTION: The cutting tool continues rotating for a
–
few seconds after the engine is turned off.
Put the tool down only after the cutting tool has
–
completely stopped and the motor is turned off.
When the cutting tool is damaged, it must be re-
–
placed at once.
Always use the original line only. Never use a metal
–
wire instead of the nylon line.
Tool and cutting tools must be properly inspected
–
and serviced periodically. Damages must be re-
paired by a service center.
Only use accessories recommended by the manufac-
–
turer. See Maintenance/Accessories
Never use metal multi-piece cutting blades, cutting
–
tools with spinning chains or flail blades.
Have your tool serviced only by qualified personnel
–
and by use of original spare parts only. This ensures
that the tool will work safely in the future.
32 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Battery
Vapours may leak out in case of unauthorised use or
when using a damaged accumulator. Bring fresh air
and seek medical advice if experiencing difficulties.
Vapours may irritate the respiratory system.
m Risk of fire! Risk of explosion!
Never use damaged, defective or deformed accumu-
lators. Never open or damage the accumulator or let
it fall on the ground.
Never charge the battery in an environment with ac-
ids and easily flammable materials.
Protect the battery against heat and fire.
Battery to be used at the ambient temperatures be-
tween 10°C and +40°C only.
Never put the battery on heaters and do not expose
it to strong sunlight for a long time.
After being subject to heavy load, let the battery cool
down first.
Short circuit - do not bridge the accumulator contacts
with metal parts.
The accumulator must be packaged (plastic bag,
box) or accumulator contacts must be sealed up for
accumulator disposal, transport or storage.
Residual risks
• There will always be residual risks, even if you use
this equipment according to instructions. The fol-
lowing hazards can occur in connection with the
construction and design of this tool.
• Health hazards resulting from swinging of hand and
arm if the equipment is used for an extended peri-
od and if it is not operated or maintained properly.
• Injuries and material damage caused by ejection
of tool attachments which are unexpectedly thrown
from the equipment because of sudden damage,
wear and tear or improper attachment.
• Warning! This tool generates an electromagnetic
field during operation. Under certain circumstanc-
es, this field can affect active or passive medical
implants. In order to reduce the risk of severe or
fatal injuries, we recommend that people with med-
ical implants consult their doctor and the manufac-
turer of the medical implant before operating the
machine.
• Always start the cut with the saw chain running.
Make the cut in such a way that the saw does not
get jammed in the wood.
• Use the gripping spikes for every cut as the starting
point and always start the cut with the saw chain
running. Make the cut in such a way that the saw
does not get jammed in the wood.
• Pay particular attention to branches under tension.
• Always pull the tool out of the wood when the saw
chain is running.
• Never work with the tool above shoulder height or
with only one hand.
• Always stand away from the falling direction. Posi-