Menu Structure - Balluff BAE SA-OH-059-YI-DP02 Betriebsanleitung

BAE SA-OH-059-YI- ----
Photoelectric Sensors
8

Menu structure

Pressing the key • takes you from the measured value dis-
play to the menu or confirms the parameter selection.
A successful parameter selection is confirmed by flashing
the display twice. The menu is structured as follows:
TEACH TEA Teach
1-V-T SP1 1V1 Do-1-V-Teach SP1
2-V-T SP1 2V1 Do TP1 -> Do TP2 -> Apply
Dyn-T SP1 DT1 Start SP1 -> Stop SP1
1-V-T SP2 1V2 Do-1-V-Teach SP2
2-V-T SP2 2V2 Do TP1 -> Do TP2 -> Apply
Dyn-T SP2 DT2 Start SP2 -> Stop SP2
Dyn-T SP12 DT12 Start SP12 -> Stop SP12
Manual MAN
Amplific. AMP Amplification: 6..255*
SSC1-SP1 SC1 SSC1 Switching Point 1:
250..500*..4000
SSC1-SP2 SC1 SSC1 Switching Point 2:
250*..4000
SSC2-SP1 SC2 SSC2 Switching Point 1:
250..500*..4000*
SSC2-SP2 SC2 SSC2 Switching Point 2:
250*..4000
T-Select SEL Def.(SSC1), SSC1, SSC2,
SSC1&SSC2
ADJUST ADJ Adjust
Adj.SSC1 SC1 Adjust SSC1
SSC1 Logic LOG HighActive*, Low Active
Hysteresis HYS 3%, 6%, 12%*, 25%
Int.Time INT Integration Time: 4..32*..256 ms
Ampl.Mode AMD Auto.Ampl.*, Man.Ampl.
1PT-Offset OFS Offs.neg.*, Offs.pos., no Offset
TeachStor. STO permanent*/temporar.
Delay 1 DL1 Adjust Delay Out1
Delay Mode MOD Del:Off*, Del:Delay, Del:OneSh.
Off-Delay OFD 0*..10000 ms
On-Delay OND 0*..10000 ms
Adj.SSC2 SC2 Adjust SSC2
SSC2 Logic LOG HighActive*, Low Active
Hysteresis HYS 3%, 6%, 12%*, 25%
1PT-Offset OFS Offs.neg.*, Offs.pos., no Offset
TeachStor. STO permanent*/temporar.
Delay 2 DL2 Adjust Delay Out2
Delay Mode MOD Del:Off*, Del:Delay, Del:OneSh.
Off-Delay OFD 0*..10000 ms
On-Delay OND 0*..10000 ms
OPTIONS OPT Options
LckLocPar PLC Lock Local Parameter:
Lock OFF*, Lock ON
Easyteach ETE Off*, 1-V-T SP1, 2-V-T SP1, Dyn-T SP1
Display DIS Display Settings
Brightness BRI Lowest, Low, Medium*, High, Highest
Orientation ORT NoRotation*, 180°CW Rot
Stb Visib. STB always on, always off*, on w.touch
ShdwnTimer SHD Standby-Shutdown-Timer:
5..60*..600 s
Fact.Reset DEF No*, Yes
www.balluff.com
CONFIG CON Configuration of Operation Modes
Pin4 Funct PN4
Pin4 Mode MOD Off, Out*
Pin4 Type TYP PNP*, NPN, PushPull
Pin4 Logic LOG Normal*, Inverted
Pin4 Src SRC Delay Ch 1*
SSC1 Mode FUN
Single Pt* SIPT Single Point
Window WIND Window
Two Pt TWPT Two Point
Dyn.neg DY_N Dynamic, falling edge
Dyn.pos DY_P Dynamic, rising edge
Th.Trk neg TR_N Threshold tracking, falling edge
Th.Trk pos TR_P Threshold tracking, rising edge
PowerMode POW High, Std*, Low, Xlow
SensorMode SEN Standard*, LightArray
SpeedMode SPE Max. Switching Frequency
Standard* STSP Standard 500 Hz
Fast FASP Fast 2 kHz
Super Fast SFSP Superfast 4 kHz
Sync 6 SYN6 Sync 6 = 250 Hz
Sync 8 SYN8 Sync 8 = 150 Hz
Precision PRSP Precision 125 Hz
High Pr 25 H2SP High Precision 25 Hz
High Pr 30 H3SP High Precision 30 Hz
SyncMode SYN Auto, Master, Slave, OFF*
Pin2 Funct PN2
Pin2 Mode MOD Off*, Out, Input
Pin2 Type TYP PNP*, NPN, PushPull
Pin2 Logic LOG Normal*, Inverted
Pin2 Src SRC Delay Ch 2*, Alarm,Teach-In,
Transd.En., CounterRst
SSC2 Mode MOD
Single Pt* SIPT Single Point
Window WIND Window Mode
Two Pt TWPT Two Point
Ext.T-Mode EXT 1-V-T SP1, 2-V-T SP1, Dyn-T SP1
Pin5 Funct** PN5
Pin5 Mode** MOD Off*, Input
Pin5 Type** TYP PNP*, NPN
Pin5 Logic** LOG Normal*, Inverted
Pin5 Src** SRC Teach-In*, Transd.En., CounterRst
* Factory Defaults
** only in cable version; -DP02
english 13