Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Controls and features (Fig. 1.1)
Headstock
1
Face-plate
2
3
Carrier
Clamp lever for headstock
4
Tailstock
5
6
Live centre
7
Clamp lever for tool spindle
Clamp lever for headstock
8
Adjustment wheel for barrel
9
10 Tool support
11 Clamp lever for tool support
12 Clamp lever for height adjustment
13 Tool console
14 Lathe bed
15 Feet
m General Safety Notes
In these operating instructions we have marked the
places that have to do with your safety with this sign.
m
• Please pass on safety notes and instructions to all
those who work on the machine.
• Comply with all safety instructions and warnings on
the machine.
• Keep all safety instructions and warnings on the ma-
chine fully legible.
• Check all power supply lines. Do not use defective
lines.
• Make sure that the machine stands stable on firm
ground.
• Caution when working: There is a danger to fingers,
hands and eyes.
• Keep children away from the machine when it is con-
nected to the power supply.
• When working on the machine, all safety mechanisms
and covers must be mounted.
• Operating personal must be at least 18 years of age.
Trainees must be at least 16 years of age, but may only
operate the machine under adult supervision.
• Persons working on the machine may not be diverted
from their work.
• The working space on the machine must be free of
chips and wood scrap.
• Wear only close-fitting clothes. Remove rings, brace-
lets and other jewelry.
• For the safety of long hair, wear a cap or hair net.
• Do not wear gloves.
• Wear goggles when working.
• Note the motor rotational direction – see electrical con-
nection.
• The safety mechanisms on the machine may not be
removed or rendered unusable.
• Cleaning, changing, calibrating, and setting of the
machine may only be carried out when the motor is
switched off. Pull the power supply plug and wait for
the rotating tool to completely stop.
• Switch the machine off and pull power supply plug
when rectifying any malfunctions.
• Connection and repair work on the electrical installa-
tion may be carried out by a qualified electrician only.
• All protection and safety devices must be replaced af-
ter completing repair and maintenance procedures.
• Place the tool support as tightly as possible against
the work piece.
All manuals and user guides at all-guides.com
• The peripheral speed of wooden workpieces must not
• Note the spindle rotation – see reversing switch.
• Provide work pieces with center bores before clamp-
• Work large and imbalanced work pieces at a reduced
• Before switching on the machine, check that the work-
• Remove the chuck key or spring dowel sleeve before
• Always close the belt cover.
• Work with three- or four-jaw chucks may only be car-
• Never stop work pieces with the hand during run out.
• Work only with well sharpened tools.
• Always use both hands when using turning tool.
• Nicked tools may not be used.
• Note the correct rotational setting on the machine.
• When leaving the work place, switch the motor off. Pull
• Unplug the machine before moving, even if only slight-
Warning! This electric tool generates an electromagnet-
ic field during operation. This field can impair active or
passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
CE tested machines meet all valid EC machine guide-
lines as well as all relevent guidelines for each ma-
chine.
• The machine must only be used in technically perfect
• The scheppach wood turner has been constructed ex-
• Any other use exceeds authorization. The manufac-
• The safety, work and maintenance instructions of the
• Relevant accident prevention regulations and other,
• The scheppach machine may only be used, main-
• The scheppach machine may only be used with origi-
exceed 25 m/s. Note spindle speed diagram!
ing between pivots.
rotational speed; it may be necessary beforehand to
cut accordingly with a band saw.
piece is securely clamped.
turning the machine on.
ried out with mounted jaw chuck shield.
Never take measurements on a rotating work piece.
the power supply plug.
ly. Correctly connect the machine to the electrical
source before operating again.
m Proper use
condition in accordance with its designated use and
the instructions set out in the operating manual, and
only by safety-conscious persons who are fully aware
of the risks involved in oerating the machine. Any func-
tional disorders, especially those affecting the safety of
the machine, sholud terefore be rectified immediately.
clusively for use with wood.
turer is not responsible for any damages resulting from
unauthorized use; risk is the sole responsibility of the
operator.
manufacturer as well as the technical data given in
the calibrations and dimensions must be adhered to.
generally recognized safety-technical rules must also
be adhered to.
tained, and operated by persons familiar with it and
instructed in its operation and procedures. Arbitrary al-
terations to the machine release the manufacturer from
all responsibility for any resulting damages.
nal accessories and tools made by the manufacturer.
english 13
Werbung
Inhaltsverzeichnis
Fehlerbehebung
