General Outline; Technical Specifications - Bft Proxima Installations- Und Gebrauchsanleitung

ENGLISH
Thank you for buying this product, our company is sure that you will
be more than satisfied with its performance.
This product is supplied with an "Instruction booklet" which should
be read carefully as it provides important information about safety,
installation, use and maintenance.
This product complies with recognised technical standards and sa-
fety regulations. We declare that it is in conformity with the following
European Directive: 89/336/EEC.
WARNINGS
When wiring the devices to be programmed or checked, make
reference to the instructions contained in the present manual and
in the manuals concerning the products to which the programmer
is to be connected.

1) GENERAL OuTLINE

PROXIMA is a terminal used for programming and checking the
devices belonging to the EElink line. All the devices belonging to this
line can be programmed and their configuration checked by means
of the present device. The EElink protocol allows the programmer
to recognise automatically the parameters managed by the device
connected: PROXIMA will therefore also be able to operate on devices
from the same line which may be marketed in the future.
These are its main functions:
• full management of parameters, logics, statistics and self-diagno-
sis of the control panels compatible with the EElink protocol.
• management of all functions of the radio receivers belonging to
the INTRIC and CLONIX series, both plugged in and incorporated
in the control panels.
2) COMPOSITION (F
1) PROXIMA Programmer
2) uNIDA Interface for control units and receivers
3) uNIFLAT Multipolar cable
4) uNITRC Interface for TRC series transmitters
5) uNIMITTO Interface for MITTO series transmitters
6) POWER SuPPLY uNIT for programmer (optional)
7) EEDBASE software in CDROM for PC interface
8) 9pin Serial cable for connection to a PC (optional)
9) A-B type USB cable for connection to a PC (optional)

3) TEChNICAL SPECIFICATIONS

External power supply: 12 V
Internal power supply:..........6LR 61 type 9V rechargeable battery
"A" interface: ....................................according to RS232 standard
"B" interface: ......................................according to EElink protocol
"C" interface: .................................................. 485 serial connector
"D" interface: ............................................. CAPRI serial connector
"E" interface: ....................................................................USB port
Display: ...................... alphanumeric with 4 rows by 16 characters
Keyboard:............................................. alphanumeric with 16 keys
No. of receiver lists: .................................................................... 19
No. of control unit lists: ................................................................. 9
Degree of protection: ............................................................. IP 20
Dimensions: .................................................................see figure 2
Weight: ..............................................................................450g ca.
4) CONNECTIONS
"A" / "E" Interfaces
Interface according to RS 232/USB standard for connection to
personal computer or other accessories. The connection to the
personal computer can only be activated if the computer has been
appropriately configured and is running the programs contained in
the EEdbase pack.
PROXIMA automatically recognises the completion of the serial inter-
face connection, therefore to start communicating with the personal
computer you just need to connect the serial cable to the "A"/"E"
interface and activate the relevant program. In order to be able to
use the USB connection, you need to install in the PC the relevant
driver contained inside the CDROM of the EEDBASE software.
12 -
PROXIMA - Ver. 01
INSTALLATION MANUAL
1)
IGuRE
300 mA power supply unit socket
"B" Interface
Interface having a 14-pole connector according to the EElink owner
protocol. The device to be programmed is connected depending on
the appropriate accessory chosen from among UNITRC, UNIDA
and UNIFLAT.
For connection methods and the choice of a suitable accessory,
make reference to the instructions concerning to the device to be
programmed.
"C" Interface
Bipolar connector for 485 serial system.
"D" Interface
Connector for CAPRI serial system (see Fig. 5).
Power supply
The device is activated by means of the switch positioned on the
right-hand side of the programmer.
The device can be supplied with power by connecting it to the 12V
power supply unit by means of the socket positioned in the vicinity
of the B interface. The EElink protocol also makes it possible for
the PROXIMA programmer to be supplied by means of the power
supply for the programmed device.
In this case, PROXIMA can also be used without a battery or the
external power supply unit.
Moreover, the EElink protocol allows the device to be programmed to
be supplied with power by means of PROXIMA; this way the devices
can even be programmed before they are installed on the site.
This makes it possible to save considerable time and simplify
work.
Batteria Ricaricabile Interna
Internal Rechargeable Battery
The programmer is provided with an internal rechargeable battery
which allows it to be used even without an external power supply.
Before being able to use it after the purchase, a full recharge is
required (15 h approx.), which is simply obtained by leaving the
programmer connected to the 12V power supply unit.
Note: the battery recharging process is active independently of the
programmer activation status; greater efficiency is however obtained
by leaving the programmer switched off.
To obtain maximum working life for the internal rechargeable battery,
you are advised to follow a few generic rules:
- after the battery discharge warning has been displayed, recharge
the battery as soon as possible;
- do not leave the programmer in charging mode for over 24
hours;
- in the case where the programmer is left unused, you are advised
to recharge the battery periodically, as necessary;
- activation of the display backlighting remarkably reduces battery
life;
- when possible, you are advised to use the external 12V power
supply unit to give power to the control units or receivers through
the EELINK connector.
In the case where critical and long operations have to be carried
out (for ex. Importing high-capacity receiver lists or transferring data
to/from a PC), you are advised to use the 12V power supply unit in
order to avoid possible loss of data due to battery discharging.
Warning: in case of replacement, exclusively use 6LR 61 type
rechargeable batteries.
Battery removal
When removing the batteries, keep to the current regulations
and in particular:
1) Remove the batteries before disposing of the products.
2) Batteries must be scrapped in a safe way.
3) The appliance must be disconnected from the power supply
during battery removal.