Start-Up Quick Guide For Open-Loop Applications - Danfoss VLT Compressor Drive CDS 803 Bedienungsanleitung

VLT® Compressor Drive CDS 803
Operating Guide
7 Green LED/On: Control section is working correctly.
8 Yellow LED/Warn.: Indicates a warning.
9 Flashing Red LED/Alarm: Indicates an alarm.
10 [Back]: For moving to the previous step or layer in the navigation structure.
11 [▵] [▿] [▹]: For navigating among parameter groups and parameters, and within parameters. They can also be used for set-
ting local reference.
12 [OK]: For selecting a parameter and for accepting changes to parameter settings.
D. Operation keys and indicator lights
Table 14: Legend to Section D
13 [Hand On]: Starts the motor and enables control of the drive via the LCP (disabled on 18.5–22 kW (22–30 hp)).
[2] COAST INVERSE IS THE DEFAULT OPTION FOR PARAMETER 5-12 TERMINAL 27 DIGITAL INPUT. IF THERE IS NO 24 V SUP-
PLY TO TERMINAL 27, [HAND ON] DOES NOT START THE MOTOR. CONNECT TERMINAL 12 TO TERMINAL 27.
14 [Off/Reset]: Stops the motor (Off). If in alarm mode, the alarm is reset.
15 [Auto On]: The drive is controlled either via control terminals or serial communication.

4.2 Start-up Quick Guide for Open-loop Applications

Table 15: Settings for Open-loop Applications
Parameter Option
Parameter 0-01 Language [0] English[1] Deutsch[2] Francais[3] Dansk[4] Span-
ish[5] Italiano[28] Bras.port
Parameter 0-06 GridType [0] 200–240 V/50 Hz/IT-grid[1] 200–240 V/50 Hz/
Delta[2] 200–240 V/50 Hz[10] 380–440 V/50 Hz/IT-
grid[11] 380–440 V/50 Hz/Delta[12] 380–440 V/50
Hz[20] 440–480 V/50 Hz/IT-grid[21] 440–480 V/50
Hz/Delta[22] 440–480 V/50 Hz[30] 525–600 V/50
Hz/IT-grid[31] 525–600 V/50 Hz/Delta[32] 525–600
V/50 Hz
Parameter 0-06 GridType [100] 200–240 V/60 Hz/IT-grid[101] 200–240 V/60
Hz/Delta[102] 200–240 V/60 Hz[110] 380–440 V/60
Hz/IT-grid[111] 380–440 V/60 Hz/Delta[112] 380–
440 V/60 Hz[120] 440–480 V/60 Hz/IT-grid[121]
440–480 V/60 Hz/Delta[122] 440–480 V/60 Hz[130]
525–600 V/60 Hz/IT-grid[131] 525–600 V/60 Hz/
Delta[132] 525–600 V/60 Hz
0–999
Parameter 0-60 Main
Menu Password
Parameter 1-13 Compres- [24] VZH028-R410A[25] VZH035-R410A[26]
sor Selection VZH044-R410A[27] VLZ028[28] VLZ035[29]
VLZ044[30] VZH088[31] VZH117[32] VZH170
0–200 Hz
Parameter 3-03 Maximum
Reference
Danfoss A/S © 2019.12
N O T I C E
Default
[0] English
Size related
Size related
0
Size related
200 Hz
Programming
Function
Select the display language.
Select the operating mode for re-
start after reconnection of the
drive to mains voltage after a
power-down.
Select the operating mode for re-
start after reconnection of the
drive to mains voltage after a
power-down.
Define the password for access
to the LCP.
Select which compressor to use.
The maximum reference is the
highest obtainable by summing
all references.
AQ32174876762701-000101 / 130R0627 | 21