Product Description; Intended Use; Scope Of Delivery - Bosch FSA 500 Originalbetriebsanleitung

3.

Product description

3.1

Intended use

The FSA 500 is a portable tester for use in motor vehi-
cle workshops.
The FSA 500 is suitable for the checking of vehicles
with spark ignition, Wankel and diesel engines and
can be used for testing all the electrical and electronic
systems on passenger cars, commercial vehicles and
motorcycles.
The FSA 500 picks up vehicle-specific signals and
relays them via Bluetooth or the USB interface to a
PC/Laptop (not included in the scope of delivery).
FSA 500 CompacSoft [plus] must be installed on the
PC/Laptop.
!
The FSA 500 is not suitable for use as a measuring
instrument for test drives.
!
The maximum permissible measurement volt-
age at the Multi measurement inputs is
60 VDC/30 VAC/42 VACpeak. FSA 500 is therefore
not to be used for checking isolation from the supply
on electric and hybrid vehicles.
FSA 500 CompacSoft [plus] features the following
functions:
R
Motor vehicle identification
R
Settings
R
Test steps for checking spark-ignition and diesel
engines
R
Multimeter measurements for voltage, current and
resistance
R
Signal generator (e.g. for checking sensors)
R
Component test (checking of vehicle components)
R
Characteristic curve tracer
R
4-channel/2-channel universal oscilloscope
R
Ignition oscilloscope Primary
R
Ignition oscilloscope Secondary
R
Insulation measurements with FSA 050
(special accessory)
For the assessment of measurement results, confirmed
"go" measurement curves can be stored as reference in
the measurement system.
Robert Bosch GmbH
Product description | FSA 500 | 23
3.2 Prerequisites for operation with
FSA 500 CompacSoft [plus]
PC/Laptop with operating system WIN XP SP2 (32 Bit),
WIN Vista (32/64 Bit), WIN 7 (32/64 Bit) or WIN 8
TM
(32/64 Bit) and at least one vacant USB interface for
the Bluetooth USB adapter or USB connecting cable.
Minimum requirements for PC/laptop:
R
CPU Intel / AMD Dual-Core 1.1 GHz or higher
R
RAM 1 GB
R
DVD drive
R
Minimum 5 GB available hard disk space
The current version of FSA 500 CompacSoft [plus]
must be installed on the PC/laptop or on DCU 130.
!
The FSA 500 CompacSoft [plus] software and
FSA 7xx/FSA 050 CompacSoft [plus] software can-
not be installed on DCU 130 or on PC/laptop simul-
taneously.
i
For motor vehicle identification via customer data or
key numbers as well as for control unit diagnosis with
CAS[plus], the latest ESI[tronic] software (Info type
A and C) must be installed on the PC/Laptop and
released. Control unit diagnosis is possible only with
a KTS module. This is subject to additional cost.
3.3

Scope of delivery

Designation
FSA 500
Power supply unit
with power cord
USB connecting cable (3 m)
Connecting cable B+/B–
Clip-on trigger
Primary connecting cable (UNI 2)
Multi measurement lead CH1
Multi measurement lead CH2
Measurement lead with voltage divider
Current probe 1000 A
Coupling with hose
Remote trigger
Secondary measuring transducer
Passenger vehicle temperature sensor
Connection terminal, black
Bluetooth USB adapter
Case
CompacSoft [plus] CD
DVD ESI[tronic]
Operating instructions
Test prod set
Accessory set with
Black and red test prods
Black and red pick-off clips
Black, red, gray adapter connectors
en
Order number
–
1 687 023 592
1 684 461 106
1 684 465 562
1 684 460 286
1 687 225 018
1 684 461 185
1 684 460 288
1 684 460 289
1 687 224 301
1 687 225 019
1 686 430 053
1 684 463 828
1 687 225 017
1 687 230 068
1 684 480 022
1 687 023 449
1 685 438 644
1 687 005 084
1 687 729 601
1 687 729 605
1 689 989 115
1 689 979 922
1 684 485 362
1 687 016 118
|
1 689 989 115 2013-08-30