Optional Accessories; Preliminary Operations - Comet K series Bedienungs- Und Wartungsanleitung

• Guarantee certificate;
• Assistance centres booklet;
• Nozzle cleaning pin.
If there are problems, contact your dealer or an authorised assistance centre.
The following range of accessories can be added to the standard high-pressure cleaner equipment:
• Sandblasting lance: designed for sanding surfaces, removing rust, paint, incrustations, etc.;
• Pipe flushing probe: designed for unblocking pipes and ducts;
• Rotating nozzle lance: designed for the removal of stubborn grime;
• Foaming lance: designed for a more efficient distribution of detergent;
• Different types of lances and nozzles.
INSTALLATION FITTING OF MOBILE VERSION ACCESSORIES
• Insert the handlebar (2) into the steel pipes that protrude from the machine and secure by means of the supplied kit:
screw (9) and retainer (40).
• Insert the holder (7) or the hose reel (12) into the housing hole (41) and secure it with screw (9).
• If the hose reel is present, connect the quick-fit connector (36) of pipe (42) to the water outlet connector (16)
and fully tighten the ring nut by hand.
FIG. )
• If the hose reel is not present, connect the quick-fit connector (36) of pipe (35) to the water outlet connector (16)
and full tighten the ring nut by hand.
(SEE FIG. 2)
• Screw the high-pressure pipe connector (43) to the thread of the gun (24) and fully tighten with two 22 mm spanners
(not supplied).
OPERATION A IN FIG. 9
• Insert the filter (18) into the water inlet connector (17). Insert the seal (26) into the water inlet hose connector (25)
and screw it to the connector (17).
• Place the high-pressure water cleaner in its workstation. The
the handlebar (2). The
• Fully unwind the high-pressure pipe (35).
• Using a flanged clip (not supplied), fix a feed pipe with an internal diameter of 19 mm/0,75 in to the water inlet
hose connector (25).
OPERATION C IN FIG. 9
• Open the mains water supply tap, and make sure there are no drips (or introduce the suction pipe into the tank).
• Check that the master switch (1) is in position "0" and connect the plug.
• Place the master switch (1) into position "1".
• Press the lever (22) of the gun, and wait for a continuous jet of water to exit.
• Place the master switch (1) into position "0", connect the lance (29) to the gun (24), and tighten it fully.
IN FIG. 9
STANDARD OPERATION (AT HIGH-PRESSURE)
• Check that the nozzle head (30) is not in the detergent distribution position (see also paragraph
).
DETERGENT"
• Start the high-pressure cleaner again, placing the master switch (1) into position "1".
• Press the lever (22) of the gun, making sure that the jet from the nozzle is even and that there is no dripping.
• If necessary, adjust the pressure by means of knob (8). Turn it clockwise to increase the pressure and anti-clockwise
to decrease the pressure.
• The pressure is indicated on the pressure gauge (13).
The detergents recommended by the manufacturer are over 90% biodegradable.
Refer to the label on the detergent packaging for use instruction.
• Place the master switch (1) into position "0".
• If aspirating from the high-pressure cleaner's tank (19), unscrew the cap (11) and taking care not to spill the liquid
(maximum capacity 3.5 l/ 0.92 US gal), fill the tank with detergent, diluted as required.
• In order to clean the detergent tank (19) thoroughly, it can be removed from its location by turning the device (21)

OPTIONAL ACCESSORIES

SEE FIG. 7
OPERATION B IN FIG. 9
OPERATION C IN FIG. 9

PRELIMINARY OPERATIONS

version must be moved by two people using the handles (27).
PICK-UP
.
OPERATION WITH DETERGENT
OPERATION B IN FIG. 9
version with wheels must be moved using
MOBILE
OPERATION D IN FIG. 9
GB
SEE FIG. .
(SEE
SEE FIG. 6
OPERATION E
"OPERATION WITH
15