Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1224 Threading Machine
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
Service
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Specific Safety Information
WARNING
This section contains important safety information
that is specific to this tool.
Read these precautions carefully before using the
1224 Threading Machine to reduce the risk of
electrical shock or other serious injury.
SAVe ALL WARNINGS ANd INSTRuCTIoNS
FoR FuTuRe ReFeReNCe!
Keep this manual with machine for use by the operator.
Threading Machine Safety Warnings
• Keep floor dry and free of slippery materials such as
oil. Slippery floors invite accidents.
• Restrict access or barricade the area from by-
standers when the workpiece extends beyond the
machine to provide a minimum of one meter (three
feet) clearance from the workpiece. Restrict ing ac -
cess or barricading the work area around the workpiece
will reduce the risk of entanglement.
• Do not wear gloves. Gloves may be entangled by the
rotating pipe or machine parts leading to personal
injury.
• Do not use the machine for other purposes such as
drilling holes or turning winches. Other uses or
modifying this machine for other applications may
increase the risk of serious injury.
• Secure the machine to a bench or stand. Support
long heavy pipe with pipe supports. This practice
will prevent the machine from tipping.
• While operating the machine, stand on the side
where the operator control switch is located.
Operating the machine from this side eliminates need
to reach over the machine.
• Keep hands away from rotating pipe and fittings.
Stop the machine before wiping pipe threads or
screwing on fittings. Allow the machine to come to
a complete stop before touching the pipe. This
4
practice will reduce the risk of entanglement in rotating
parts.
• Do not use this machine to install or remove (make
or break) fitting. This practice could lead to trapping,
entanglement and loss of control.
• Do not operate the machine without all covers
properly installed. Exposing moving parts increases
the probability of entanglement.
• Do not use this machine if the foot switch is bro-
ken or missing. The foot switch provides safe control
of the machine, such as emergency shutoff in case of
entanglement.
• One person must control the work process, ma -
chine operation and foot switch. Only the operator
should be in the work area when the machine is run-
ning. This helps reduce the risk of injury.
• Never reach into the machine front chuck or rear
centering head. This will reduce the risk of entan-
glement.
• Read and understand these instructions and the
instructions and warnings for all equipment and
materials being used before operating this tool to
reduce the risk of serious personal injury.
If you have any question concerning this RIDGID
– Contact your local RIDGID
– Visit RIDGID.com to find your local RIDGID contact
point.
– Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com, or in the U.S. and
Cana da call (800) 519-3456.
description, Specifications
And Standard equipment
description
The RIDGID
®
Model 1224 Threading Machine is an elec-
tric motor-driven machine that centers and chucks pipe,
conduit and bolt stock and rotates it while cutting, reaming
and threading operations are performed. Threading dies
are mounted in a variety of available die heads. An integral
oiling system is provided to flood the work with thread cut-
ting oil during the threading operation.
With proper optional equipment, the 1224 Threading
Machine can be used to thread larger pipe, short or close
nipples or for roll grooving. The 1224 machine can also be
used to cut standard grooves on pipes and to cut or strip
the saran and plastic lined pipes.
®
product:
®
distributor.
940-713-030.09_REV. G
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
