Cleaning And Care - WMF Lono Gebrauchsanweisung

Slow Cooking
1. Fill the Slow Cook insert (2) with the desired food. In order to retain cooking fl avours, the food
should be quickly fried fi rst.
2. Place the water tank (4) on the main appliance (5).
Note: The appliance will not work without the water tank.
3. Insert the Slow Cook insert into the water tank. Then fi ll the water tank with as much clean water
as is required to completely cover the Slow Cook insert.
Note: The contents of the Slow Cook insert must be fully immersed in water from the outside to
ensure optimum temperature transfer. Note the
Cook" on the back of the water tank. You can now slow cook using a pre-set custom cooking time
or individually programmed temperature and cooking time settings. Proceed as described in the
section on "Sous Vide cooking" in steps 4 to 9.
Note: When you remove the water tank from the device after use, a small residual amount of
water will spill from the pump onto the top of the main appliance. This is normal. Remove the
mains plug and empty the main appliance into the sink.
Setting the temperature unit (°C/°F) and water hardness
1. Place the water tank (4) on the main appliance (5).
2. Connect the appliance to the mains. The appliance is now in standby mode. Press the settings
button (9) and hold it down for at least 3 seconds. If the appliance is already in standby mode,
press the settings button (9) and hold it down for at least 3 seconds.
3. The °C icon fl ashes. By twisting the selector knob (12), you can change the setting to °F. In this
case, the preset temperature of 60°C is replaced with 140°F. Confi rm your selection by pressing the
selector knob again.
4. Instead of the time, the preset water hardness H4 now fl ashes on the display. By twisting the
selector knob, you can adjust this to H1 to H4 according to the water hardness where you live.
Note: You can fi nd out your water hardness from your council or from your energy and water
provider or online.
5. Once you have confi rmed the water hardness set, it is permanently saved in the device.
6. Then press the on/off button (7) to put the appliance into standby mode.
Hardness range Hardness
1 Soft 0 – 7° dH
2 Medium >7 – 14° dH
3 Hard >14 – 21° dH
4 Very hard > 21° dH

Cleaning and care

Cleaning
Pull out the mains plug and allow the appliance to cool down.
Do not immerse the appliance in water, the surfaces can be cleaned using a damp cloth and a little
washing-up liquid. Do not use any sharp or abrasive cleaning agents.
18
MIN and MAX marking "Slow
Dishwasher-safe
Glass lid (1)
Slow Cook insert (2)
Adjustable meat and vegetable
holder (3)
Water tank (4)
Main appliance (5)
Scale indicator
Limescale deposits increase the time it takes the Sous Vide Cooker to heat up. They also lead to energy
losses and impair the service life of the appliance.
The automatic scaling indicator determines the time for the next descaling cycle. Depending on the
level of use and hardness level of the water, you are prompted to run a descaling process by the fact
that the descaling light is permanently lit.
Descaling agent
Use a commercially available descaling agent that is also suitable for fi lter coffee machines. Use a commercially available descaling agent that is also suitable for fi lter coffee machines.
Do not use regular or concentrated vinegar because this may damage the materials in the
appliance. appliance.
Use of descaling agents based on citric acid may lead to the formation of precipitates that seal the
limescale layer or clog up the lines in the appliance. Descaling with citric acid also takes too long, as a
result of which complete descaling cannot be guaranteed. result of which complete descaling cannot be guaranteed.
Our warranty does not cover damage caused by using unsuitable descaling agents or failure to
follow the descaling instructions. follow the descaling instructions.
Handle descaling agents carefully to prevent damaging furniture or clothing.
Descaling the appliance
Place the water tank (4) on the main appliance (5). Connect the appliance to the mains. The
appliance is now in standby mode. Press the on/off button (7) to switch the appliance on. Press the
settings button (9) and hold it down for 3 seconds. "CALC" is now shown on the display instead of the
temperature. Now press the start/stop button (8) to start the descaling process. The settings cannot be
changed.
Warning: The
symbol only goes out once the descaling process has been completed. Once you have
fi nished the descaling process, press the on/off button (7) to put the device into standby mode.
Can be rinsed Wipe off with a
under running damp cloth
water
19