Schleicher XCx 1200 series Betriebsanleitung Seite 136

SAVE_Q_PARAM_* ........................................................... 99
SAVE_R_PARAM_* ........................................................... 99
SEND_MAIL ..................................................................... 101
SET_DATE ....................................................................... 100
SET_SERC_COMMAND .................................................... 99
SET_SERC_PHASE........................................................... 99
SET_TIME ........................................................................ 100
UBA_ERR_CTRL ............................................................. 103
URCV_V ............................................................................. 98
USEND_V ........................................................................... 98
UZB_VR ............................................................................ 103
WRITE_AXIS_PAGE ........................................................ 103
WRITE_FILE ..................................................................... 101
WRITE_PROFILE_INT ..................................................... 101
WRITE_PROFILE_REAL ................................................. 101
WRITE_PROFILE_STRING ............................................. 101
WRITE_Q_PARAM_* ......................................................... 99
WRITE_RP ....................................................................... 103
WRITE_SERC_PARAM ..................................................... 99
XFIO_CONFIG ................................................................. 101
XRIO_STATE ................................................................... 101
Funktionsbausteine und Bibliotheken ...................................... 96
Grundinitialisierung .................................................................. 81
HALT Betriebszustand ............................................................. 92
Handbetrieb ............................................................................. 88
Hardware-Konfiguration
Einlesen .............................................................................. 54
I/O-Konfiguration einfügen .................................................. 57
Optionen ............................................................................. 59
Hochlaufverhalten der SPS ..................................................... 83
HyperTerminal ....................................................................... 123
I/O-Ebene ................................................................................ 52
I/O-Treiber CANopen ............................................................... 69
Inbetriebnahme .................................................................. 28, 90
RS232-Schnittstelle .......................................................... 123
Initialisierungsdatei ProConOS.ini ......................................... 104
Installation ............................................................................... 28
AddOns ............................................................................... 31
MULTIPROG ...................................................................... 30
OPC-Server ........................................................................ 30
Schleicher-Dialog................................................................ 32
Systemvoraussetzungen .................................................... 28
Interrupt
Beispiel-POEs..................................................................... 63
Eingänge ............................................................................. 61
Taskstruktur ........................................................................ 65
UBE 32 0,1I ........................................................................ 61
Variablen für Verarbeitung .................................................. 61
IP Configuration ..................................................................... 125
Koppelspeicher
Datenstruktur .................................................................... 121
Einfügen .............................................................................. 48
Hilfe ................................................................................... 120
nichtremanenter (non retain) Bereich ............................... 121
remanenter (retain) Bereich .............................................. 121
Übersicht ........................................................................... 119
Variablen und Tasks ......................................................... 119
Versionsauswahl................................................................. 50
Zugriff .......................................................................... 49, 120
LED-Anzeigen
Ethernet und Sercos III ....................................................... 21
Steuerung ........................................................................... 20
Log-Book ................................................................................. 91
Log-Datei, von MFA erzeugt.................................................... 85
Memory-Management-Unit ...................................................... 11
MFA (Multi Function Application) ............................................ 82
MMU ........................................................................................ 11
Montage ................................................................................... 14
136
MULTIPROG
Bibliotheken und Funktionsbausteine ................................. 96
Einbindung von ProCANopen ............................................. 75
Installation ........................................................................... 30
Netzwerkvariablen .............................................................. 71
Neues Projekt ..................................................................... 44
Projekt kompilieren und senden ......................................... 46
Projektbaum ........................................................................ 44
Multi-Task-System ................................................................. 107
Netzgeräte ............................................................................... 26
Netzwerk-Schnittstelle
Computername ................................................................... 35
Hausnetz-Adresse .............................................................. 34
Inbetriebnahme ................................................................... 33
Kommunikationsschema..................................................... 34
Local Area Connection ....................................................... 37
PC-Adresse ........................................................................ 34
PING-Befehl ........................................................................ 41
Programmierung mit MULTIPROG ..................................... 41
RtOS Virtual Network .......................................................... 39
TCP/IP-Einstellungen anpassen ......................................... 36
Textformular ........................................................................ 40
Vorbereitung ....................................................................... 33
VxWorks-Adresse ............................................................... 34
Windows-Adresse ............................................................... 34
Netzwerkvariablen ................................................................... 71
NFS and Hardlink .................................................................. 129
OPC-Server
Installation ........................................................................... 30
Koppelspeicherdaten .......................................................... 119
PAC ......................................................................................... 11
PDD Process Data Directory ................................................... 80
PDO ......................................................................................... 67
PING-Befehl............................................................................. 41
PNSCommunicating .............................................................. 102
Prioritäten der Tasks ............................................................. 115
ProCANopen
Einbindung in MULTIPROG ............................................... 75
erste Verbindung ................................................................ 76
Installation ........................................................................... 74
Konfiguration mit ................................................................. 73
Konfigurationsmanager auswählen .................................... 78
POE CANdemo ................................................................... 79
Test der Netzwerkverbindung ............................................. 79
Process Data Directory ............................................................ 80
Process Data Objects .............................................................. 67
ProConOS ............................................................................. 104
ProConOS.ini ......................................................................... 104
Programm, Zuweisen zu Task ............................................... 117
Programmable Automation Controller ..................................... 11
Programmieren ........................................................................ 89
Programmierung der SPS ....................................................... 92
Projektbaum ............................................................................. 44
Remote Desktop UltraVNC .................................................... 131
Remote-Zugriff ....................................................................... 131
Reset-Taster ............................................................................ 22
RS 232 / RS 422 / RS 485-Schnittstellen ................................ 19
RTOS Settings ....................................................................... 130
Schleicher X-Manager ........................................................... 125
EWF Configuration ........................................................... 128
IP Configuration ................................................................ 125
NFS and Hardlink ............................................................. 129
RTOS Settings .................................................................. 130
Schleicher-Dialog
Installation ........................................................................... 32
Steuerungsmenü ................................................................ 88
Schnittstellen ........................................................................... 16
CAN .................................................................................... 19
Betriebsanleitung XCx 1100 / XCx 1200 ● Version 01/14
Anhang