Equipment Description; Assembly; Features And Controls; Operation - Briggs & Stratton BPW2500 Bedienungsanleitung

Equipment Description

Read this manual carefully and become familiar
with pressure washer. Know its applications,
its limitations, and any hazards involved. Save
these original instructions for future reference.
This pressure washer operates at a max of 17.2 MPa (2,500
PSI or 172 BAR) and a flow rate of up to 8.7 liters (2.3 gallons)
per minute. This high quality residential system features 25.4
cm (10") wheels, axial cam pump with stainless steel pistons,
automatic cool down system, detergent siphoning system, quick
connect spray tips, heavy duty 9.1 m (30') hose, and more.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use, ask
dealer or contact qualified service center. NEVER operate
units with broken or missing parts, or without protective
housing or covers. DO NOT by-pass any safety device
on this machine. DO NOT modify pressure washer in any
way. This equipment is designed to be used with Briggs &
Stratton Corporation authorized parts ONLY.

Assembly

Attach Handle and Accessory Tray
1. Place handle (1, A) onto supports (1, B) and align holes (1, C).
2. Insert carriage bolts (2, A) through holes from outside
of unit, attach with plastic knob (2, B) and tighten.
3. Place accessory tray (3, A) over holes (3, B) on
handle and push tree clips (3, C) into holes.

Features and Controls

A Spray Gun
B Nozzle Extension
with Quick Connect
Accessory Tray
C
D Fuel Tank
E Warning Tag
F Throttle Lever
G Air Filter
H Water Inlet

Operation

Oil Recommendations Figure
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Clean area around oil fill (4,M) and remove oil fill cap/
dipstick.
Figure 1 2 3
Figure 4
J Pump
K Automatic Cool Down
System
Detergent Siphoning Tube
L
M Oil Fill
N Recoil Starter
P High Pressure Hose
R Spray Tips
6
4 7
3. Verify oil is at Full mark (top hole) (7,A) on dipstick.
4. If needed, slowly pour oil into oil fill opening to Full
mark (top hole) on dipstick. DO NOT overfill.
5. Replace and tighten oil fill cap/dipstick.
NOTICE DO NOT attempt to crank or start engine before
before it has been properly serviced with recommended oil.
This could result in an engine failure.
CAUTION Avoid prolonged or repeated skin contact
with used motor oil. Used motor oil has been shown to
cause skin cancer in certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Add Fuel
Figure 8
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For high
altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Use of unapproved fuels could damage
pressure washer and voids warranty. DO NOT use
unapproved gasoline such as E15 and E85. DO NOT mix
oil in gasoline or modify engine to run on alternate fuels.
To protect the fuel system from gum formation, mix in a fuel
stabilizer when adding fuel. See Storage. All fuel is not the
same. If you experience starting or performance problems after
using fuel, switch to a different fuel provider or change brands.
This engine is certified to operate on gasoline. The emission
control system for this engine is EM (Engine Modifications).
WARNING! Fuel and its vapors are
extremely flammable and explosive which
could cause burns, fire or explosion resulting in
death or serious injury. Turn pressure washer engine off and let it
cool at least 2 minutes before removing fuel cap. Loosen cap
slowly to relieve pressure in tank. Fill fuel tank outdoors. DO NOT
overfill tank. Allow space for fuel expansion. If fuel spills, wait until
it evaporates before starting engine. Keep fuel away from sparks,
open flames, pilot lights, heat, and other ignition sources. Check
fuel lines, tank, cap and fittings frequently for cracks or leaks.
Replace if necessary. DO NOT light a cigarette or smoke.
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank (B).
Be careful not to overfill. Allow about 4 cm (1.5") (C) of
tank space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
5