Chronograph Models - Georg Jensen C30-ST01 Bedienungsanleitungen

Operating Instructions: Quartz Watches
Chronograph
Models : D42-ST03, D46-ST03, K41-ST03, S42-ST03, S46-ST03
F
A
60
30
25 5
G
20 10 40 20
15
12
10 2
8 4
8
H
D
Setting the time:
1. P ull the crown out to position 3, its maximum extension. The second hand (C) will stop moving.
2. T urn the crown either clockwise or anti-clockwise until the watch hands (A and B) are positioned at
the desired time.
3. W hen the desired time is reached push the crown back to position 1 and screw down if applicable.
NOTE: When the hour hand passes 12 o'clock, the watch is set at midnight if the date changes. If the
date does not change, it is set at noon.
Setting the date:
1. Pull the crown out to position 2.
2. Turn the crown clockwise until the desired date appears in the date window (D).
3. W hen the desired date is reached push the crown back to position 1 and screw down if applicable.
NOTE: Do not change the date between 10pm and 2am as this may damage the movement.
B
Display & control buttons
I
A : Hour hand
B : Minute Hand
C : Second Hand
1 2 3
D : Date window
F : Centre stop second
G : 30-minute counter
C
H : 12 hour counter
I : Start / stop pusher
J
J : Re-set pusher
1 1
Chronograph: Basic Functions (Start, Stop & Reset)
1. To start timing, press the start stop pusher (I)
2. T o stop timing, press the start / stop pusher (I) again
3. E lapsed time can be read as follows: hours: 12 hour counter (H) minutes: 30-minute counter (G)
seconds: second stop hand (F)
4.To reset, press the reset pusher (J)
Chronograph: Basic Functions (Start, Stop & Reset)
1. To start timing, press the start stop pusher (I)
2. T o stop timing, press the start / stop pusher (I) again
3. T o resume timing, press the start/stop pusher (I) again
4.To stop timing, press the start / stop pusher (I) again
5. E lapsed time can be read as follows:
hours: 12 hour counter (H) minutes: 30-minute counter (G) seconds: second stop hand (F)
6. To reset, press the reset pusher (J)
NOTE: accumulated timing sessions can be continued by repeating steps 2 and 3 above
Chronograph: Interval Timing
1. To start timing, press the start stop pusher (I)
2. To show timing interval, press the reset pusher (J) interval timing will be displayed. Timing continues
in the background.
3. T o show measured time, press the reset pusher (J) again, the chronograph hands will advance
quickly to the measured time.
4.To stop timing, press the start / stop pusher (I)
5. F inal time can be read as follows:
hours: 12 hour counter (H) minutes: 30-minute counter (G) seconds: second stop hand (F)
6. To reset, press the reset pusher (J)
NOTE: further intervals can be displayed by repeating steps 2 and 3 above
Chronograph: Adjusting the chronograph hands
Occasionally you may find that the chronograph counters do not return to zero. Follow these steps to
correct them.
1. Pull out the crown to position 3
2. S imultaneously push the start/stop (I) and reset pushers (J) and hold for two seconds. The centre stop
second (F) will make a fast revolution to indicate that adjustment mode has been activated.
3. P ress the start/stop pusher (I) to advance centre stop second hand (F) to the desired position.
4.Press the reset pusher (J) once to activate the 12 hour counter (H)
5. P ress the start/stop pusher (I) to advance 12 hour counter (H) to the desired position.
6. P ress the reset pusher (J) once to activate the 30-minute counter (G)
7. Press the start/stop pusher (I) to advance 30-minute counter (G) to the desired position.
8.Once complete return crown to position 1.
1 2