Operating Instructions; Remote Control; Switching On The Remote Control; Remote Control Led Blink Code And Audio Signal - Truma Mover XT Gebrauchsanweisung, Einbauanweisung

Operating instructions

Remote control

LED 1 2 3 4
b
h
i
Fig. 2

Switching on the remote control

a = On/Off slide switch
On (LED 4 lights up*)
Off (LED 4 goes off)
* LED 4 flashes for approx. 5 seconds after the remote con-
trol is switched on, until the system is ready for operation.
The following options are available for controlling the caravan:
b using the control knob only
c using the slide control only
b + c using the control knob and the slide control
On the control knob, the caravan symbol indicates the current
direction of travel (of the caravan).
The slide control allows the caravan to be moved forwards
and backwards without jerking, with infinitely variable speed
control.
Slide control only
(Forwards, backwards and infinitely variable speed control)
– Push slide control forwards -> caravan moves
forwards (in the direction of the drawbar)
(both wheels rotate forwards)
– Pull slide control backwards -> caravan moves
backwards (in the opposite direction to the drawbar)
(both wheels rotate backwards)
The further the slide control is moved from the zero position,
the higher the speed.
Control knob only Mover® XT
(Right or left curve, infinitely variable)
– Turn to the right -> caravan drawbar moves to the right
left wheel rotates forwards – right wheel rotates backwards
rotation around middle of caravan
– Turn to the left-> caravan drawbar moves to the left
left wheel rotates backwards – right wheel rotates forwards
rotation around middle of caravan
The caravan can be rotated on the spot without being moved
forwards.
Control knob and slide control Mover® XT2
It is not possible to rotate on the spot without forward motion
because there are two axles. If the control knob and the slide
control are operated, the Mover® XT2 moves in a circle, with
the outside motor in continuous operation and the inside
motor in pulsed operation.
Control knob and slide control Mover® XT / XT2
(Caravan right or left and forwards or backwards)
– Turn control knob to right and push slide control forwards ->
a
– Turn control knob to left and push slide control forwards ->
c
– Turn control knob to right and pull slide control backwards ->
h
i
– Turn control knob to left and pull slide control backwards ->
Speed increases the further the slide control is pushed
forwards the end stop (freely selectable turning radius and
speed).
Engaging and disengaging
h = Two-handed operation disengagement of drive rollers
i = Two-handed operation engagement of drive rollers
In order to engage and disengage the drive rollers, both
buttons must always be pressed simultaneously – for
approx. 3 seconds (safety delay) – until the engaging or
disengaging of the drive rollers commences.
The buttons can be released when the drive rollers are moving
in the direction of the respective end position.
The drive rollers automatically reach their end position.
rollers are disengaged and automatically move to their end
position.
The remote control switches itself off automatically:
– after approx. 2 minutes if none of the buttons are pressed
– after approx. 7 minutes if one of the movement buttons is
To reactivate the remote control, move slide switch to "Off"
and then back to "On"
There is no "On/Off" switch on the caravan itself.
Remote control LED blink code and audio signal
LED 1 red
LED 2 yellow lights up in the event of a temporary malfunction
LED 3 red
caravan drawbar moves to right
left wheel rotates fast – right wheel rotates slowly forwards
caravan drawbar moves to left
left wheel rotates slowly – right wheel rotates fast forwards
caravan drawbar moves to right
left wheel rotates slowly – right wheel rotates fast backwards
caravan drawbar moves to left
left wheel rotates fast – right wheel rotates slowly backwards
(drive rollers swing away from tyres)
(drive rollers swing towards tyres)
If the two buttons for disengaging are pressed whilst the
rollers are engaging, engaging is interrupted, the drive
permanently held down. The green LED 4 goes off.
after approximately 1 second.
indicates state of charge of caravan battery
good LED off
medium LED flashes slowly (0.5 Hz)
low LED flashes fast (1 Hz)
poor LED stays on continuously
(e.g. overvoltage/overtemperature)
Switch remote control off and on again (in
the case of overtemperature, wait for end of
cooling-off phase if necessary).
lights up in the event of a persistent malfunction
and an audio signal is emitted, e.g. if the
Mover® XT / XT2 is engaged and the plug has
been pulled out of the safety socket
flashes in combination with audio signal
e.g. if a drive motor is defective
17