Remote Control Battery Change; Manoeuvring The Caravan; Coupling To A Towing Vehicle; Maintenance - Truma Mover XT Gebrauchsanweisung, Einbauanweisung

LED 4 green flashes if radio connection is poor or not yet
established after remote control is switched on
lights up when remote control is ready for
operation and the data link is stable
flashes in combination with acoustic signal
– for approx. 5 seconds after switching the
remote control on, until the system is ready
for operation
– 13-pin plug not plugged into safety socket
All LEDs "off" and no audio signal
System off
(check batteries in remote control if necessary)

Remote control battery change

Only use micro-batteries that will not leak,
type LR 03, AAA, AM4, MN 2400 (1.5 V).
When inserting new batteries, take care not to reverse the
positive and negative terminals.
Fig. 3
Empty, used batteries can leak and damage the remote
control! Remove the batteries if the remote control is
not being used for a long period of time.
No warranty given for damage caused by leaking
batteries.
Before disposing of a defective remote control, always
remove the batteries and dispose of them correctly.

Manoeuvring the caravan

Follow the "Safety Precautions" before using the
Mover® XT / XT2.
Apply parking brake if caravan is uncoupled.
Disconnect 13-pin plug from vehicle and plug into safety
socket of caravan.
For safety reasons, the Mover® XT / XT2 can only be
operated if the 13-pin plug of the caravan is plugged into
the safety socket.
In the event of a malfunction, the 13-pin plug must not
be removed from the safety socket, otherwise the elec-
tronic safety functions will be disabled.
Switch on remote control – green LED 4 flashes in combina-
tion with the audio signal for approx. 5 seconds until the
control unit is ready for use.
Press the two buttons (i) for engaging simultaneously, and
engaging will start after approx. 3 seconds (safety delay).
Use the position indicator to check that both drive rollers
are correctly engaged.
Before starting the Mover® XT / XT2,release the parking
brake.
Movement in all directions is possible using the control knob
and the slide control.
18
In the case of the Mover® XT, the end stops on the control
knob (left and right end stops) can also be used to rotate the
caravan on the spot (around its vertical axis).
The Softstart/Softstop makes the caravan start to move
without jolting, and brakes it gently when stopping.
When the control knob or slide control are released, or if the
radio signal is interrupted or becomes too weak, the caravan
stops moving. Radio equipment and other Mover® remote
controls will not activate your Mover®.
After start-up, the Mover® XT / XT2 moves at a steady speed
(according to the setting on the slide control). Speed increases
slightly on downhill slopes and decreases on uphill slopes.
After manoeuvring, apply the parking brake first and then
disengage the drive rollers from the tyres.
Move slide switch on remote control to the "Off" position
to switch the remote control off (the Mover® XT / XT2
switches to standby mode).
The slide switch also acts as an "Emergency Stop"
switch.
Remove plug from safety socket after manoeuvring, otherwise
the battery will be discharged. Quiescent current with plug
inserted approx. 80 mA.

Coupling to a towing vehicle

The Mover® XT / XT2 allows a caravan to be coupled to a
towing vehicle without jolting and with millimetric precision.
However, this requires care and a degree of practice.
Following the operating instructions, move the caravan close
to the towing vehicle (apply parking brake and engage gear).
In order to position the caravan precisely, operate the control
knob or slide switch until the caravan's coupling is located
precisely over the ball coupling on the towing vehicle. Then
couple the caravan to the vehicle by lowering it at the support
wheel in the usual manner.
Prepare the caravan for towing in the usual way.
The caravan must not be towed with the drive rollers
engaged.

Maintenance

Keep drive elements clear of coarse road dirt. When cleaning
the caravan, spray the Mover® XT / XT2 with a water hose to
remove mud etc. Make sure that no stones, twigs etc. are
trapped in it. The control unit does not require servicing. The
remote control must be kept in a dry place.
Clean the Mover® XT / XT2 as described above every year
(or before overwintering). Do not park the caravan with the
drive rollers engaged.
To prevent the battery from becoming totally discharged
during long periods of inactivity it must be disconnected and
recharged before using again. Charge the caravan battery
before starting up.
It is extremely easy for you or your caravan dealer to perform
the checking and maintenance of your Mover® XT / XT2 dur-
ing the annual inspection of your caravan. In case of doubt,
please contact Truma Service (see Truma Service Booklet or
www.truma.com).