Checks; Emergency Disengagement; Troubleshooting; Tuning The Electronic Control Unit To The Radio Remote Control - Truma Mover XT Gebrauchsanweisung, Einbauanweisung

Checks

– Check the installation, wiring and connections for damage
at regular intervals. The drive assemblies must be able to
move freely and be returned automatically to the safe idle
position when they are disengaged. If this is not the case,
check the drive assemblies for dirt or corrosion on their
guides and clean them if necessary to ensure they can
move properly.
– After a prolonged period of non-use (e.g. overwintering),
check that all motors respond correctly to commands from
the remote control.
– At least every 2 years, an expert must check the
Mover® XT / XT2 for rust, check that detachable parts are
firmly attached and check that all safety-related parts are in
good working order.

Emergency disengagement

If the caravan battery is discharged to the extent that electri-
cal disengagement no longer works, or if a defect is present,
disengagement can also be performed manually.
Prise out the plastic cap (m) at the rear end of the cover using
a screwdriver. Attach socket wrench (WAF 7 – included in
scope of delivery) to hex bolt and disengage drive assembly
by rotating anticlockwise. Repeat procedure at opposite side.
Fig. 4
Once the battery has been charged, the rollers can be
engaged electrically again.

Troubleshooting

Check that the batteries in the remote handset are in immacu-
late condition!
Check whether the caravan plug has been plugged into the
safety socket!
Check whether the caravan battery is in immaculate condition
and is fully charged! Please note that battery performance can
deteriorate considerably at cold ambient temperatures.
Check that the fuse in the battery connector cable is in order.
If the fuse is defective, check the connector cable for possible
short circuits.
Perform a reset (approx. 10 seconds - briefly disconnect bat-
tery or disconnect and reconnect safety plug)!
If these actions do not remedy the problem, please contact
Truma Service.
Tuning the electronic control unit to the
radio remote control.
If the control unit or the remote control is replaced, they
must be tuned to each other again in accordance with the
instructions below.
Check that installation has been carried out in accordance
with the installation instructions, and make sure that the drive
rollers are not engaged. Check that the battery is properly
connected and in good condition, and that the control unit is
being supplied with 12 V. Make sure that the caravan connec-
tor is plugged into the safety socket.
Switch off remote control.
Press and hold the reset button (k) on the control unit
(red LED – j – flashes slowly), and after approx. 5 sec the
LED (j) flashes rapidly. Release the reset button and within
10 sec press and hold button (c) – Engage – on the remote
control, at the same time switching the remote control on
using the slide switch (a).
m
Fig. 5
The remote control and the control unit are now tuned to one
another. Once tuning is complete, the red LED (j) comes on
and stays on.

Technical data

Operating voltage
12 V DC
Power consumption
on average approx. 28 A up to a maximum of 150 A
Quiescent current consumption
< 80 mA (with plug inserted)
< 150 µA (with plug removed)
Radio frequency
Class 2, 868 MHz
Speed
approximately 17 cm per second
(depending on weight and incline)
Weight
approx. 28 kg
Positive line fuse
150 A
Mover® XT range of use
single-axle caravans with a gross weight of up to 2300 kg
Mover® XT2 range of use
dual-axle caravans with a gross weight of up to 2400 kg
Right reserved to make technical changes!
The remote control and the control unit are tuned to one
another in the factory.
j
k
a
c
19