Reparation; Content Of Delivery / Necessary Accessories - Reely HOTLANDER NEXT GENERATION Bedienungsanleitung

4 p

REpARATION

4.1 c
ONTENT Of DELIvERy
s
cOpE Of DELIvERy
One Chassis
-
- 2,76 ccm two stroke glow engine
with 1,5 kW (1,7 PS), with
manifold, resonance tube, air filter and pull starter,
already mounted
- fuel hoses, already laid.
- Four wheels with plastic rims and
already mounted Monster Truck tires
- Monster-Truck car body, imprinted
- Splints to fasten car body
- A plastic tube as guidance for the wire aerial
- these installation and operating instructions
HOTLANDER NEXT GENERATION RTR:
- one three-channel remote control
(pistol grip transmitter)
- Steering servo, Throttle/brake servo and receiver,
already mounted
s p
pARE ARTs
The spare part list can be found on our Website www.conrad.com in the Download domain specific to the corresponding product.
Alternatively, you can order the spare parts by phone; the contact details are at the beginning of this operating manual in chapter
"Introduction".
A
ccEssORy REcOMMENDATION
Which type of fuel is the right one?
The selection of the fuel has an impact on the performance characteristic of the engine.
However, as a matter of principle:
- In the running-in phase, a special RC car fuel with approximately 15% nitromethane should be used.
- After the run-in of the engine (after a mere operating time of approximately 45 minutes), you can change to a fuel with approximately 0%
nitromethane.
- For maximum output, we recommend the max. percentage of 5% nitromethane
Use fuel for RC cars only!
The percentage of oil contained in fuel for RC plane engines is too small (too little lubrication), which causes the engine to overheat, thus lea-
ding to serious damages. The same is valid for vehicle gasoline.
Why is a tank bottle needed?
RC model car fuel is available in big bulks (canisters) only. Filling the tank by using a smaller, special tank bottle with a small, curved pouring tube is
significantly simpler. You also prevent spilling fuel (expensive and poisonous).
Are more glow plugs necessary?
Glow plugs wear, especially in the running-in phase. Therefore, we recommend having some glow plugs ready in case of
need for a replacement. There are glow plugs with different calorific values; the selection of the glow plug has a big impact
on driving performance. For the running-in phase, you should use a "hot" glow plug for high performance engines. After the
running-in phase, you can use a glow plug with a middle or a "cold" calorific value.
Use glow plugs for RC cars only! A wrong glow plug, such as e.g. for 4 stroke plane engines, lets the engine run incorrectly and
complicates the tuning.
Replacing the glow plug
To that effect, you need an extra long plug spanner (spider wrench SW 8, 9, 10 and 1), which can
be used also to unscrew the outer hexagonal screws.
Sparking the glow plug
A plug connector (long) with start battery or a plug connector with rechargeable battery as a unit is inserted on the glow
plug and heats the latter, so that the air-fuel mix sparks off and the engine starts. When the engine runs smoothly, the plug
connector can be removed.
© REELY 01/08
,
NEcEssARy AccEssORIEs
R
EquIRED AccEssORIEs
N
OT INcLuDED IN THE DELIvERy
-
-
-
-
-
-
Also available as a complete set
Nitrobox II Combuster no. 23 07 99
incl. transport box
-
-
12 accumulators for the transmitter and the receiver
Glow plug and
plug spanner
Plug connector with rechargeable battery as a unit and
battery charger
Tank bottle
Charger (230V AC) for the rechargeable batteries or
quick charger to connect to a 12V car battery
Model fuel methanol/oil based,
minimum share 5% - 10% nitromethane
:
39