KEB COMBIVERT F0 V1.2 Betriebsanleitung Seite 136

Summary Standard Parameters
OPERATION PARAMETERS
PAGE 41-44
o.0 Boost 1)
o.1 Minimum reference 1)
o.2 Maximum reference 1)
1)
o.6 Acceleration time
o.8 Deceleration time 1)
1) 2)
o.13 Input source
o.14 Delta - Boost 1)
o.15 Delta - Boost time 1)
o.16 S-curve acceleration time
o.17 S-curve deceleration time
LEVEL PARAMETERS
PAGE 54-56
1)
L.0 Axtual value level 1
1)
L.1 Actual value level 2
L.2 Load level 1 1)
1)
L.3 Load level 2
L.6 DC dynamic braking level 1)
L.7 DC dynamic braking voltage
L.8 DC dynamic braking time 1)
L.16 Timer value 1)
1)
L.17 Timer adding value
CUSTOMER PARAMETERS
PAGE 62-70
C.0 Limit of maximum reference
1) 2)
C.2 Rotation lock
C.4 Condition display
C.5 Noise filter / digital inputs
C.7 DC-braking mode 1) 2)
1)
C.8 Carrier frequency
C.9 Parameter group l ock
C.10 Output voltage stabilization 1) 2)
C.12 Baud rate
C.13 Inverter address
1)
C.14 Zero clamp speed
1) 2)
C.15 Select mode of modulation
C.21 Watchdog time
C.25 Control word activation
C.27 Application selection
136
r.0 Prom no.
r.1 Inverter status
r.2 Actual value display
r.3 Set value display
r.4 Output voltage
r.5 DC voltage
r.6 DC circuit peak voltage
r.7 Current inverter utilization
r.8 Peak load
PROTECTION PARAMETERS
P.0 Stall prevention level
P.1 ACC/DEC time during stall prevention
P.2 Stall torque characteristic
P.3 LAD stop load level
P.4 U/f-function
P.6 Speed search condition
P.7 Automatic retry UP
P.11 Energy-saving mode
1)
P.12 Energy-saving level
1) P.13 LAD stop condition
P.14 LD stop DC voltage level
P.15 Load-dependent set shifting level
P.21 OH switch-off time
d.0 Rated frequency
d.1 f-mode
d.2 Lower modulation limit
d.4 Rated motor power
d.18 Slip compensation / frequency gain
1)
d.19 Slip compensation / auto torque gain
d.20 Slip compensation / min. frequency
d.21 Slip compensation / max. frequency
d.22 Slip compensation / no-load losses
d.23 Slip compensation/load-no-load differ. display
d.24 Number of pole pairs
INFORMATION PARAMETERS
1) I.0 Inverter type
I.1 Rated inverter current display
I.2 Output frequency limit display
I.3 Error counter OP
I.4 Error counter UP
I.5 Error counter OC
I.6 Error counter OH
I.7 Error counter OL
I.8 Error counter set selection
I.9 Error counter watchdog
I.15 Software identification
I.16 Software date
1) Parameters, that can be changed in the parameter sets 1...6 !
2) Parameter value is stored after pressing the ENTER-key twice !
RUN PARAMETERS
PAGE 37-40
PAGE 45-50
1)
1)
1) 2)
1)
1)
1)
1)
1) 2)
1)
1)
1)
1)
DRIVE PARAMETERS
PAGE 57-61
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
PAGE 75-76
Parameters for Standard Applications!
r.14 Input terminal status
r.15 Output terminal status
r.18 Bus address display
r.19 Reference setting 1)
r.20 Rotation setting 1) 2)
r.21 Password input
r.22 Select parameter group
r.23 Select parameter set
r.29 Current frequency
INPUT / OUTPUT HANDLER
PAGE 51-53
H.0 Presetting mode reference value
H.1 Logic of analog inputs 1) 2)
H.3 Output logic 1) 2)
1) 2)
H.4 Out1-function
H.5 Out2-function 1) 2)
2)
H.7 Input logic
H.8 In-function parameter set 2)
H.9 Analog output function 1) 2)
1)
H.10 Analog output offset y
H.11 Analog output gain 1)
FREE-PROGRAMMABLE PARAMETER SETS
PAGE 71-74
F.0 Key parameter set no.
F.3 Based on para set
F.4 Global enter
F.5 Clear top parameter set
F.6 Bus parameter set no.
F.7 Save last bus parameter
PROFILE PARAMETERS
PAGE 77-79
Pr.4 Pole number
Pr.5 Malfunction code
Pr.6 Control word
Pr.7 Status word
Pr.8 Nominal speed value
Pr.9 Actual speed value
Pr.10 Speed-min-amount
Pr.11 Speed-max-amount
Pr.16 Acceleration-delta speed
Pr.18 Acceleration-delta time
Pr.25 Deceleration-delta speed
Pr.27 Deceleration-delta time
Pr.37 Speed reference value
1) 2)